2000 Ford Focus - Page 4 - Answered Questions & Fixed issues

When you first turn the key on, no crank, if you listen close to gas tank, can you hear the fuel pump run for a few seconds? If not, check proper voltage and ground at the fuel pump connector, engine cranking. I have to ask, how long since a tune-up? Are there any applicable trouble codes? Anything else missing? engine cranking do you have spark at the spark plugs and fuel injector pulse?

Ford Focus 2000 2007 Factory Workshop Service Manual for better result download the pdf file

They are known to have broken wiring in the drivers door jam the wires break from the door being open and closing ,I think there s recall for the harnesses for the front doors I could be wrong but check the harnesses on the drivers door the wires break at the connector just pull back the rubber around the harness?

Not sure about the Ford Focus issue?? If your motorized bicycle has wire spokes, they should be adjustable. Just tightening the spokes will pull the rim to that side. The opposite when loosening them etc.If your wheels are of the mag type like a car, then maybe a bike shop can straighten out the wobble without more damage.

remove the rear seat cusion, thare should be a cover under the cusion with 4 screws take these out and under should be the fuel pump.

My first suggestion is always recurring to a qualified mechanic.
In your particular case there is an issue with Focus fuel pump, and Ford guarantees free replacement in many countries, ask to your local dealer, to find out if you can have fuel pump replaced for free.
FORD FOCUS Recall - FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
2000-02 focus spi fuel pump problems - Focaljet
fuel pump in a 2000 ford focus SE
If you wnat to DIY, instead, buy the haynes manual, and follow step by step illustrated guide. Fuel pump replacement is not a complex operation.

Willard, normally inside your automatic transmission. check the link below. Ford Focus Shift Solenoid Repair P0750 P0753 P0972

Brake light behind the brake pedal is stuck. under the dash free the plunger the brake pedal pushes and oil it. As to the cruse control that could be a lot of things. Hope this helps mike

Check your battery and your battery posts, charge your battery if necessary, check your charging system.

Check battery for voltage, terminal condition, fuses, try jump starting or swapping out battery...

There is a front and back side of the cam gears. Some marks are dots by the gear tooth, some are notches cut out.

according to autodata belt replacement guide , there are no timing ,marks on the cam gears it require special tools and a good knowledge of mechanics to do the job so I strongly recommend that you get a workshop manual before starting on the job I could type it all for you but with only two fingers , I would be here until next week as the directions are involved and you will need diagrams to full understand the procedure that is why I suggest a workshop manual the procedure is not as you would expect as on other engine makes and need to carefully followed

The brake switch is probably mis-adjusted. If it does not activate when the brake pedal is depressed, the brake lights will not light and the gear shift release solenoid will not activate. That, or the wiring harness is not connected properly to the switch or is damaged.

Buy a new one, very cheap, and you can look it up on YouTube and it will explain all. Good luck.

remove transmission .do research find out what all tools needed.and type of fluid. make sure to have car stable and safe while under.might have to remove more than just the trans depends on car.make sure to place throw out bearing correctly seated in place are you would have done it all for nothing. cheak and make sure you have fluid in the container .break fluid will work just might be out of fluid.youtube has alot of vids

make sure that the child lock has not been moved first small lever at the edge of the door that is moved to lock the door after children are in the car

Hi there, cars are all electrical these days, buy a cheap code reader off of eBay ( item no. 361240488837 ) plug it into your diognaustic plug and it will give you a problem code so you know what's wrong with the car, a booklet comes with the code reader with the codes in it, sometimes it will throw up a code which isn't in the booklet so then you have to google the code, hope this helps :)

Power comes from the ignition relay via the key switch. The relay also powers several other circuits. The key switch activates the relay so that those circuits are not powered directly from the key switch.

On this website you find fuse box diagram description for Ford Focus mk1 Ford Focus MK1 fuse box diagram Auto Genius

B1600 At some time since last clear the ignition was switched on without any key code being read. P0113 Intake Air Temperature Sensor 1 Circuit High Bank 1 P0179 Fuel Composition Sensor Circuit High In the back of the trunk of these cars are a box on the left hand side looking in the truck under the cosmetics of the floor, lift all that up and you will see a small box that you can reset, that goes out and you can not start the car, that goes to your fuel pump. Try, hope that is all that it is, because the codes do not reflect the starting problems you are having. Good Luck!