Top 20 1993 Nissan Pickup Questions & Answers

hi if you think the four wheel drive it not being use it very likely that the link that engages the four wheel it rusty or the gear shift inside the gear box will not slide by some wearing abstraction caused by wear and tear

Inside door handle should have some screws that need to be removed and the window crank will have a c-clip behind it . or some you have to pop the cover off the window crank

Possibly a bad connection on the positive side coming from the battery or a weak ground. Check where the leads join the terminal clamps. Has the battery been verified as good? It doesn't take a lot of amps to run lights but it does to turn over the engine. Jump starting it does not require a fully charged battery.

Have an alignment done. It requires specialized equipment

Can you do a compression test? There may be something amiss with the piston or valve.. and it's usually the exhaust valve that has burnt/split, allowing compression to be kicked straight out of the exhaust. The symptom of a burnt/split exhaust valve is akin to a misfiring spark plug

Nissan Pickup For the easy solution download the pdf file

Could be bad speed sensor.

missing can be from vacuum leaks, faulty injectors , low fuel pressure, faulty coil, ignition module, low voltage from faulty alternator or bad battery supplying less than required voltage to the electrical system

Here's a link on replacing your alternator. Repair Guides Engine Electrical Alternator AutoZone com

NISSAN should have an online manual or their are websites dedicated solely to manuals.

there are only 2 kinds pull off, and unscrew off. you didnt look first? is this a , i cant find it? question. remove the cap, they have 3 kinds on all cars screws, twistlocks, and tabs watch like a zillion folks do this on youtube yet. or read the sevice manuals or login to alldata.com and see it? step by bitty step there

open the tailgate, you should see the screws behind that assembly http://www.carcarekiosk.com/video/1995_Nissan_Pickup_XE_3.0L_V6_Extended_Cab_Pickup/lights/tail_light video is just an illustration i'm attaching a pdf copy of the service manual so you can see the actual drawing on page BF-7 http://www.nicoclub.com/FSM/Hardbody/1988%20d21%20nissan%20navara%20pathfinder%20terrano%20service%20manual/Section%20BF.pdf

How about checking your ignition switch you coulld have a faulty wire connection.... Good Luck!

open the hood and see

if the test was just recently done have the customer go back to the place that did the test and ask for another printout. that`s the only way to get the readings.

Need a LOT more info. Model,4wd?,disc or drum. You will need special tools to make it a lot easier. Whats wrong with the rear brakes?

You will have to find bolts that fit the drum.on the drum over the brakes has 3 places on it that has places where you have to screw the bolts into to remove the drum. Once you have the bolts in the drum turn bolts in a little bit at a time going until bolts eventually push drum off of brake shoes.the bolts you need should be metric bolts. I believe the bolts are 13 to possible 14 or 15 mili meter
Go to the hardware store and get 3 sets of 13,14,15 mm bolts 3 of the bolts should fit.once you have the brake drum off start on one brake shoe at a time. Lay your parts out on the ground one thing at a time better yet take a picture first and remove parts one thing at a time on ground so you know where and how they go back on. Make sure you have two cans of brake clean to spray brake drum down and spray where all the parts hook up to plate where brake shoes hook to until somewhat are clean.then make sure that you match up the brake shoe lining with the proper brake shoe, one brake shoe lining will be longer than the other. Should say primary or secondary. Just match them up with same length lining lenghth.if this doesn't help go to utube and pull up your year of truck make and model. Hope this helps.

Have you checked the fluid level?

Signal switch needs to be replace. Check ebay.

Must pull starter then ground starter to the negative of the battery then take a jumper cable to the positive post of the starter or just take state to your local parts store they will test it free