20 Most Recent 1988 Nissan 200SX - Page 4 Questions & Answers


check the main fuse in the engine bay there is 2 one is 80amps check that one. as for the starer the solinoid is stuck if you have to hit it to get it to work.

Nissan 200SX... | Answered on Feb 20, 2014


Throttle position switch could be the problem

Nissan 200SX... | Answered on Feb 11, 2014


1998 Nissan/Datsun 200SX 1.6L SFI DOHC 4cyl

The Fuel Filter is located: Under hood, driver side, rear engine area, passenger side of master cylinder, mounted in fuel line,just guessed at your year,

Nissan 200SX... | Answered on Feb 10, 2014


If you take out the module that controls the tone your overhead interior light will no longer work.

Nissan 200SX... | Answered on Jan 11, 2014


sounds like a stretched gear shift cable or the linkage on the tranny may need some adjusting i would start with the linkage first jack vehicle up and do a visual while some one goes through the gears make sure to use jack stands so that the power wheels are off the ground.....good luck

Nissan 200SX... | Answered on Nov 09, 2013


I use crazy glue and some patient and work fine. Put a little on the other side of the broken key, push back into ignition and hold for a couple of minutes until dry, when removing pull fast, if fail try again. I have a Sprinter and the keys are prone to breaking already happen twice and both time I got it out with crazy glue.

Nissan 200SX... | Answered on Oct 22, 2013


first you need to get that fixed. check your manual.

Nissan 200SX... | Answered on Jul 16, 2013


Your e-brake cable that is connected to back brakes could be binding,cable could be bad,remove both bake drums and inspect brake shoe with cable connected to it.Also check inside drum for scoring and brake shoes,if worn uneven,replace both sides.

Nissan 200SX... | Answered on Nov 27, 2012


Sounds like the timing belt/chain slipped

Nissan 200SX... | Answered on Oct 06, 2012


The cable is probably too tight,andnot allowing the pressure plate to use all of its clamping force. This will also wear out the new release bearing.

Nissan 200SX... | Answered on Sep 26, 2012


It is just a few screws (look closely), and then a gentle pull on the panel...There are spring clips holding it in as well.

Nissan 200SX... | Answered on Sep 16, 2012


check fuse or connection to horn touch hot wire from pos. of battery to horn prong where plugs up to make sure horn works

Nissan 200SX... | Answered on Sep 03, 2012


I don't know about you, but, my 97 sx se got a clogged catalytic converter and they honed in out rather than replace it...my gas milage went up to 41 mpg, but the emissions...well..you know..might have cat checked

Nissan 200SX... | Answered on Aug 31, 2012

Not finding what you are looking for?
Cars & Trucks Logo

45 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1996 Nissan 200SX
1996 Nissan 200SX

139 Questions

1998 Nissan 200SX
1998 Nissan 200SX

120 Questions

1995 Nissan 200SX
1995 Nissan 200SX

-47 Questions

1997 Nissan 200SX
1997 Nissan 200SX

87 Questions

1986 Nissan 200SX
1986 Nissan 200SX

-14 Questions

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

200SX Nissan

  • 200SX Nissan

Most Popular Question

1998 200sx shuts down after about 5

  • Cars & Trucks
Loading...