1992 Chevrolet K1500 - Answered Questions & Fixed issues

First of all, there is no wire that runs from the horn to the steering column (if the horn circuits had been properly diagnosed you would know this). I would recommend diagnosing and repairing the horn circuit the correct way rather than butchering your wiring harnesses and adding more problems to the electrical problems that you are already experiencing.

If you would like help with diagnosing and repairing your truck's horn circuit, I would be happy to help you do that.

1992 Chevrolet... | Answered on Jun 03, 2019 | 2,038 views

you must remove two nuts to steering column to drop it down to rest on seat then there will be two small bolts 8mm remove these and unplug wires its bolted to the steering column its self also the high beam switch uses the same bolts pay carful attention to exact location it has a little ajustment to it the holes are elongated must be put in the same place as the one you remove

1992 Chevrolet... | Answered on Feb 09, 2019 | 70 views

if your losing fluid the slave cylinder is probably failing or the clutch master cylinder is got bad seals either way one must be replaced the slave cylinder is in the bellhousing and tranny must be dropped

1992 Chevrolet... | Answered on Feb 09, 2019 | 36 views

You're wasting both time and money on a vehicle that is not worth the $$ you would have to spend to repair it - if you can at all. Junkyard, dude. Sorry. I replaced the leaf springs and hangers on a '03 Silverado several years ago - $1,000. I did it because I only paid $2,500 for the truck, which was otherwise OK.

1992 Chevrolet... | Answered on Feb 01, 2018 | 109 views

Whats your temp guage reading?

1992 Chevrolet... | Answered on Jan 21, 2018 | 39 views

I saw what you replaced, didn't see any testing? Any applicable trouble codes? Use a gage and check proper fuel pressure, TBI--9--13 psi. As an example, 5 psi fuel pressure makes a nice looking injector spray pattern, but, 5 psi won't start and run a v8. My opinion.
Could be other issues.

1992 Chevrolet... | Answered on Nov 13, 2017 | 177 views

alldatadiy.com or eautorepair.net will have schematics. Or, call your local library and see if they have those services for free

1992 Chevrolet... | Answered on Sep 26, 2017 | 48 views

AC compressor when activated will ALWAYS draw some power from engine. Ergo less acceleration and gas mileage.

1992 Chevrolet... | Answered on Aug 28, 2017 | 214 views

Being a single piston master i do not see how it could be holding pressure on the the slave cylinder. if your clutch petal is releasing high you need a new clutch and pressure plate

1992 Chevrolet... | Answered on May 29, 2017 | 54 views

You said you jumped the wires for the pump? Was that at the pump relay?
If you have a voltmeter or test light, keep the jumper wire in place and check for voltage at the fuel tank connector. The pump wire will be gray. With relay out and jumpered there, you should have battery voltage at the fuel tank connector. The key doesn't even have to be on, cause the relay has voltage to it at all times. If you jumpered it right (terminals 87 and 30 on the relay), and no voltage at the tank connector, you have a broken fuel wire somewhere between the relay and the fuel tank.
If you do have voltage at the tank, but the pump still won't work, only two possibilities, a bad pump or the ground for the pump is lost. Check the pump ground first.

1992 Chevrolet... | Answered on May 23, 2017 | 51 views

probably why the wire was disconnected in the first place
talking with an accredited transmission specialist shop will give you clues as to if the solenoid replacement will fix the fault before you splash the cash

1992 Chevrolet... | Answered on May 07, 2017 | 385 views

Sounds like you have the actuator switch set to tight. You might want to try to adjust the switch so it has a little room between the switch and the shifter. Hope this helps.

1992 Chevrolet... | Answered on Apr 12, 2017 | 195 views

it is very possible that the clutch master cylinder has malfunctioned
what happens in your case is that there is a compensating port in the cylinder that becomes blocked and when the clutch is released the fluid is pushed back by the pressure plate fingers
it has no where to go so so the plate is held in a partial or fully disengaged position causing it to slip
it would be good workshop practice to replace both the slave and master cylinder with new units then bleed the air out
it is a very common practice for mechanics to replace the clutch leaving the customer with an extra bill when all it was ,was the master cylinder

1992 Chevrolet... | Answered on Apr 02, 2017 | 76 views

Best Manuals

for the best solution of your problem visit this site

1992 Chevrolet... | Answered on Apr 20, 2016 | 44 views

Sounds like a wire is shorting out. Trace it back and see if there's a bare spot touching metal. Hope that works

1992 Chevrolet... | Answered on Sep 23, 2015 | 247 views

How To Fix A Lock On A 1989 chevy k1500 truck - YouTube

? 38:45
Jul 19, 2012 - Uploaded by TheManKaveShow
This is an easy and quick way to fix a lock on a 1989 - 1993chevy truck! ... 1985 Chevy C30 Power Door LockTroubleshooting & Repair ...

1992 Chevrolet... | Answered on Aug 05, 2015 | 229 views

Not finding what you are looking for?
1992 Chevrolet K1500 Logo

590 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts


Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides