1994 Dodge Caravan - Answered Questions & Fixed issues

bingo transfer smoked

The sliding door ajar switch has a tan/yellow and black wire going to the switch. Chrysler has issued a service bulletin for this problem and issue a bumper pad to prevent inadvertent door ajar warning. Try to find bulletin 08-21-94

for a belt to run off the pulleys , one of the pulleys will not be mounted parallel to all the other pulleys check alternator pulley for alignment, power steering for alignment and tensioner pulleys for alignment place a long straight edge across the faces of the pulleys to another pulley and see if it touches both side of the pulleys check the idler pulley for failing bearings that will not allow that pulley to run in line under tension

Make sure the battery is disconnected and the airbag.

If you don't have the equipment to check the system take it to Auto Zone, etc, and have them check the system. Just because it is a new part doesn't insure it is good. They can also run a check for the codes. Both checks should be without charge.

The check engine light could relate to something else - not your battery or alternator. If your battery isn't charging from the alternator an illuminated battery symbol would appear. It could be many things - low oil level, low coolant level, low windscreen washer fluid level. It could even be an electronic 'fault' - which a computerised diagnostic check would identify. If the battery warning light is illuminated the first thing you should do is to check the tension of the alternator belt. You say that a new battery and alternator have been fitted? Take it to an auto electrician - he should identify any fault within minutes.

most likely a manual gear box is it jumping out of gear indicates the the gear is not properly engaged --adjust linkages check gear lever for obstructions in mounted on the tunnel loose /incorrectly tensionedd bell housing bolts failed rear engine mounts drive line vibrations or possible badly worn gear teeth jumping out of gear is when the mating gears are not exactly in line and the slight angle makes one gear walk out of mesh with the other.

Either the wheel bearing is bad or you do not have the axle all the way into the transmission

If you are saying the front axle is having issues with a vibration while driving then you should take it back to the mechanic that did the work. The other things that need to be checked are the bearings and the cv joints. Also don't forget the tires, they could bee out of balance too.

Check answer to other post with the same question.

Sounds like a fuel issue. Hook a fuel pressure gauge to the fuel rail and start the van. You should have at least 40lbs of pressure. Unfortunately for you, Dodge put everything in the fuel tank as a unit, so if it is just a plugged fuel filter you are still looking at a high repair bill.

What engine?

Oil level may be low. Check your oil.

Here you go joe.a guide to do the job. Repair Guides Steering Ignition Switch And Lock Cylinder Assembly...

depending how bad the head is on it if it is a star head get a Philips screw driver tap it down on screw with hammer just to shock it spray some WD40 on it let it sink in see if you can turn the screw a fraction just to get it up a bit if head then buggers up get a mole grips grip it onto screw and turn it slowly that way i have done many like that hope info is usefull

Look at a Factory Wiring Diagram No other way

A loud low knock? And it sounds like a disel now, sounds like one of your rod bearings is going bad. Basically, unless you want to put a new motor in it or have the one in it rebuilt, the only thing you can do is drive it till it blows. Sorry to be the one to give you bad news like this, but your motor is old. Parts are worn out. You either have to freshen it up or let it die.

old car. If you want simple guessing , just wait it will com.e... long: on new cars, it be lack of engine power (or DTCs stored showing bad problems, with LEAN fuel, or EGR stuck open or throttle motor sticking) but back WHEN its vastly more crude and simple and problematic. I'll answer for USA cars. and stock systems, all the above same but not throttle elect. motor. no throttle by wire then/. there are 2 systems, vacuum mech. or electro mech. one yanks the throttle , the other adds metered air to control speed. just one glance at it and bingo , post a photo.? caravan ,not grand caravan which enigne, of the many, cruise parts can vary by engine type. my online shows 5 engines and not one PCM has cruise pin(s) its a separate system then, found in the last chapters in the FSM. 2 possibles.

• (engine running lean, at cruise, or misfiring) (tune up time>?)
• or the cruise parts are bad.

id say the cruised servo motor is bad or its valve. sticks. if parts are sticking clean it , lube it and it might correct. I do not have access to the servo data. at all. join a real dodge forum and get that.

Check the fuse located in main fuse box and lab led horn

Make sure the plastic shield is not missing below the pulleys which keeps road debris and excess water off belt and pulleys. Also check that the alternator or power steering pump are not slightly out of alignment.