Top 20
1986 BMW 3 Series Questions & Answers
I cant get my
You may have this
posted in the wrong product category. Please select another category
appropriate to the problem and re-post the problem so the correct
expert will see and respond to the question..
Rear tire is flat and
put car up on stands ,must be stands for security then place a wood board against wheel rim and then hit it with a 14lb hammer ,then it will come off .when putting other one on make sure the inside of the wheel hub where it contacts the wheel hub is well greased to stop it corroding on again
11/17/2010 5:29:57 PM •
1986 BMW 3...
•
104 views • 0 helpful votes
I have replaced the seal
check the splines to see if there is a flat area that lines up with the shaft, turn it till it lines up, sounds like your not lined it up straight to me.
8/24/2010 2:24:36 AM •
1986 BMW 3...
•
48 views • 0 helpful votes
Fan doesn't work
Chec your manual for locations of fan relays & fuses. It could be fried already.
6/30/2010 12:23:22 AM •
1986 BMW 3...
•
32 views • 0 helpful votes
E30 ENGINE LAYOUT
can you be a bit more precise? on what you require..do you require surpentine belt layout? an actual picture of the engine?..
2/9/2010 7:54:56 PM •
1986 BMW 3...
•
293 views • 1 helpful votes
Im buying a 1986 bmw
You can get hte codes from this BMW by turning the ignition key to the run position and then press the accelerator pedal to the floor 5 times, it will enter the diagnostic mode, count the flashes just like obd 1. Hope this helps, let me know
11/29/2009 1:42:20 AM •
1986 BMW 3...
•
479 views • 1 helpful votes
I have problems w my power windows is a bmw 1993
If all windows stop workin at once it's a relay .. That can be found under your steering wheel after you remove the panel... This relay you gotta get it at a dealership if your local auto zone don't got it... Its called a comfort relay or a power window relay... Might be blue or gray.. Call the dealership tell them to transfer your call to parts then ask away on your realay... Remove it and give them the part number theres 1 or 2 numbers on it if im correct its the longer numbers you give to them... Make sure when they pull it up on there computer its the right 1... For power Windows .. And if you got a sunroof it'll be for that too. Depends on your model Bmw.. Well good luck and Hope this helps...
8/21/2009 5:34:24 AM •
1986 BMW 3...
•
297 views • 1 helpful votes
HOW COULD I READ CHECK ENGINE CODE ON A 1986 BMW 325E???
You can't use a tool to pull codes from an '87 BMW 325(e). You have the 2.7 liter and your DME, or computer is a Motronic. If you had a 325i, then a tool could read the codes because the computer was upgraded that year to a Motronic 1.1 system with a round plug in under the screw cap on the driver's side under the hood. The only tool you can buy is the one for resetting the service interval light and resetting the oil change light. To answer your question about going about finding your driveability problem would be to get a BMW Bentley Manual. This manual shows you how to use a standard voltmeter to check everything from your computer plug in. Your computer is located above the glovebox.
Good Luck,
~Stillin~
6/5/2009 12:33:20 AM •
1986 BMW 3...
•
1,934 views • 1 helpful votes
I removed my stereo for my 86 bmw 325 and now i am
How to set up radio without wiring diagram : First you need to hook up the lead and ground power wire to your radio.(the lead usually has a line all the way down it). Turn power on to the radio and switch to am/fm. Locate any lead speaker wire and connect it to front right -. Then take all ground speaker wires one by one and touch them to front right +. As soon as you hear a sound, find out which speaker it is coming from, as soon as you have identified correct speaker remove wires from right speaker and mark them carefully. Do this with the rest of speaker lead wires an speaker ground wires and you will be able to connect your stereo.
6/16/2009 4:56:26 AM •
1986 BMW 3...
•
388 views • 0 helpful votes
Not finding what you are looking for?