1984 BMW 3 Series - Answered Questions & Fixed issues
Noise from Rear
Replace the bad Wheel Hub Bearing
Do both sides,not just the bad one.
Lots of You Tube Video on that
3/28/2014 9:48:49 PM •
1984 BMW 3...
•
Answered
on Mar 28, 2014
•
182 views
My 1984 bmw 325e DASH BOARD LIGHTS dont work
Check a couple things:
1. Verify that the dimmer switch for the dash lights isn't in the full dim position (it turns off the dash lights).
2. Check your fuse panel (in the engine compartment) for a blown fuse.
1/4/2014 12:00:49 AM •
1984 BMW 3...
•
Answered
on Jan 04, 2014
•
200 views
Battery bran new, Alternator brand
I would start at the positive terminal on the battery. Is there a separate wire to the clamp carrying the current from the alternator? It should have a fusible link in it (may not be obvious, could be just a thick spot in the wire). If the problem is not there, you will need to trace that wire forward, checking for voltage everywhere the wire is visible (poke a sewing pin through the insulation to get voltage reading)..
3/14/2011 2:11:14 PM •
1984 BMW 3...
•
Answered
on Mar 14, 2011
•
159 views
I need to know the
6? btdc is the static timing firing order 1342 ,hope this is sufficient
2/10/2011 9:26:46 PM •
1984 BMW 3...
•
Answered
on Feb 10, 2011
•
186 views
How to enter code? went
come on here for free ,anyway you press preset 1 and use either the volume or tuning buttons ,maybe even the tape buttons to place the number then when all numbers press 6 to enter the code on the venerable old classic vehicle
1/18/2011 7:11:49 PM •
1984 BMW 3...
•
Answered
on Jan 18, 2011
•
172 views
84 325e: when you 1st
It sounds like the driveshaft carrier bearing is bad, Once you reach speed the centrifical force of the driveshaft centers it and the noise goes away. Most noticable at take off.
12/28/2010 5:14:03 PM •
1984 BMW 3...
•
Answered
on Dec 28, 2010
•
217 views
Shifter-loose.wont-go-into-2nd.
You will need to remove the shifter and have a look witch bushes on the shifter is worn and replace those bushes.It is not a very difficult job and can be done by your self.
11/19/2010 1:18:37 PM •
1984 BMW 3...
•
Answered
on Nov 19, 2010
•
151 views
How do I reset the service indicator lights on my
SPEEDO~ check the cable remove the intrument panel and access the cable going into the odometer, remove it , pull cable out check it for fraid ends and lubrication IF its not fraid , use PB Blaster or WD40 on the entire cable and reinstall, if still not working correctly you will need to remove it at the transmission end and inspect the little gear.
Reset on this is done by a tool that resets it in the engine compartment, if u dont have the tool u need to ground for 10 seconds the #5 pin, DO NOT DO THIS if u are not sure how to, ALSO need to know is it a 15 pin or 20 pin connector?
9/9/2010 11:37:07 PM •
1984 BMW 3...
•
Answered
on Sep 09, 2010
•
151 views
My son has a 1984 528E BMW Sedan. He last started
How did you tell it was only sending spark to # 3 cylinder. Could be bad plug wires or very badly fouled plugs if indeed electrical, or could be an issue with the injectors or fuel system. If not sure. One quick way to test is get an inductive timing light to see if you have a spark pulse on each wire. Please give me more infor and I'll see how to help.
9/12/2010 6:22:33 AM •
1984 BMW 3...
•
Answered
on Sep 12, 2010
•
340 views
Car will not start at times. Although, once it is
yes you can do it all if your inclined. yes its possible you got good avise. When you drop the tank be sure you do it when the fuel is as empty as possible or its awkward and heavy. Also disconnect the battery when you do the starter so as not to short out anything
1/23/2010 8:23:39 AM •
1984 BMW 3...
•
Answered
on Jan 23, 2010
•
145 views
Not finding what you are looking for?