20 Most Recent 2003 Dodge Intrepid Questions & Answers

Your wiper motor most likely burnt out. And your washer fluid pump did the same.

2003 Dodge... | Answered on Oct 13, 2017

You need to find out what fault caused the check engine light to come on, until the fault code is retrieved from the engine control module memory you are 100% guessing. I think you have a misfire.

2003 Dodge... | Answered on Mar 03, 2017

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

2003 Dodge... | Answered on Sep 20, 2016

Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

2003 Dodge... | Answered on Jun 27, 2016

Please visit the site. It will be very help full for you

2003 Dodge... | Answered on May 23, 2016

You need a dealer to scan the Transmission control module for codes and to do other tests. it could be allot of issues.

2003 Dodge... | Answered on May 06, 2016

A good multi meter would do you some justice it sounds like , from new components and statement sounds like a missing ground , if the motor has been swapped out check all the fram to ground connections as well as any moter mount ground bridges , a charging system is rather simple (make a complete circuit) , wire harnesses make this a chore to trace down but provides a factory working condition ,. To just trouble shoot charging is done with the field wire to batt pos , and earth (ground) to alternator case . good luck!

2003 Dodge... | Answered on Nov 09, 2015

it could be the cooling fan relays or possibly the cooling fans. to check the fans disconnect the plug at the fans and run jumper wires to them both power and ground. if they don`t work then the fans are bad. check voltage and grounds at the plugs when they should be running, if they are good then the wiring is good. it could also be the coolant sensor for the fans that send the signal from the sensor to the computer so it knows when to turn on the fans. the fan that runs with the A/C when turned on could be the A/C relay.

2003 Dodge... | Answered on Sep 10, 2015

Two heater hoses run from the engine to the demister radiator, one hose has a tap to shut off the hot water when the air conditioner is on . this tap is not closing or has frozen in the on position , repair this and you will be fine.

2003 Dodge... | Answered on Mar 14, 2015

Dodge Says To Replace The Solenoid Pack First If Required By Date Code.

2003 Dodge... | Answered on Mar 09, 2015

bad valve internal to rack & pinion recommend replace rack

2003 Dodge... | Answered on Mar 03, 2015

2009 Mercury Mountaineer, my heater wont work unless I'm driving and get over 50 mph... I let my car warm up for 20-30 minutes and it wont defrost my windshield, it only blows cold air.

2003 Dodge... | Answered on Jan 13, 2015

Not finding what you are looking for?
2003 Dodge Intrepid Logo

419 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Dodge Experts


Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Intrepid Dodge

  • Intrepid Dodge

Most Popular Question

2003 dodge intrepid hard turning flushed

  • Cars & Trucks