Power tilt and power stearing wheel adjustments stopped working. Passenger seat side is OK. Is this a fuse problem? Is there a reset.
Posted by ourdomino on
I have the same problem. Seat and steering column just stopped working. Passenger side normal. No fuse for these components. With so many postings witht he same problem there has to be a defective or worn out source. Please post if you find a solution!
Posted on Feb 18, 2010
How do i turn off tyre puncture warning on bmw 5 series
Posted by Guest on
When your typ BMW 5.serie is E60/61 confirm air tyre presure and reset RPA (reifen pannen anzaige) in to i-Drive menu/setting/car/RPA.
When your typ BMW 5.serie is E39 ,here are systems used by the RDC and RSC!
RDC confirm tyre value and a more settled ride system itself sets the RSC and the system would have had on the center tunnel RSC she button pressed the system will reboot.
Posted on Jul 08, 2010
the indicator ligth is stil on after I change the oil
BMW insp. reset
-Ingnition OFF (pos 0)
-Press and Hold the trip odometer button while turning key to position 1 (accessory)
-Keep the button depressed (about 5 secs.) imto; upi see "Oil Service" or "Inspeciton" with "Reset" or "Re" in the display
-*Note: ON vehicles with "High" cluster, you will also see the amount of fuel (in litres) remaining until next service
-Press the button again and hold for approx. 5 secs. imto; :Reset" or "Re flashes
-While the display is flashing, briefly press the button again to reset the Service Interval. After the display has shown the new interval you should see "END SIA" for about 2 secs.
Note that if the "Reset" or "Re" does not flash, then you have not met the minimum consumption level and cannot reset.
2001 up to 2003 for shure don't know about any other models, where i found this it said 2001 to current but not shure when it was posted. Thanks
Posted on Aug 09, 2008
2002 bmw 530i key does not (remotely) unlock doors or trunk but they work fine manually.
Posted by centcomm on
Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.
Posted on Sep 19, 2010
My Bmw x5 2001 Display shows Trans Fail Safe Mode, Truck drives verry sluggish up until around 45+ mph.. then it picks up speed and drives normal. Reverse is fine, seems to be an electrical or sensor issue because it just came out of nowhere. Not sure what to do, Hoping the trans is not shot!! anyone have any answers.
sometimes it will clear if you turn the X5 off and restart it. however, it could be an early indication that the tranny is about to expire. i have had it happen and it cleared with a power cycle, but also had friends where it cleared for a few weeks/months and returned. this time it was really the transmission that went bad. if you can't get it to clear, then i'd suggest taking it to the dealer and have them plug into it to have a better look.
Posted on Jan 28, 2009
How or where can I get a fuse box diagram for a bmw x5 4.4i?
Posted by clhparsons on
my bmw has the diagram in the fuse box, try that first
Posted on Mar 22, 2010
HI I WOULD BE VERY THANKFUL IF SUM1 COULD HELP ME WITH MY PROBLEM I WAS DRIVEING TO WORK THIS MORNING ON THE MOTORWAY AND THE CAR WAS RUNNING FINE AS I PULLED OF THE MOTORWAY AND ON TO A DUEL CARRIGEWAY I ACELERATED TO OVERTAKE AND MY CAR WENT INTO LIMP MODE NOT ACCELERATEING AND JUST DYING DOWN ON ME AS THE ENGINE MANAGEMENT LIGHT CAME ON AND ALSO A WARNING ON THE DASH SAING TRANS FAILSAFE PROG WHAT COULD THIS PROBOEM BE I STOPED THE CAR FOR 10MINS AND RESTARTED IT THE WARNING LIGHT HAD CLEARED BUT NOT THE ENGINE MANAGEMENT I HOPE THIS DOES NOT MEAN THAT MY TRANSMITTION IS ON ITS WAY OUT AS IT IS QUIET COSTLY PLEASE HELP!!!!!!!!!!!!!!!!!!
Posted by big_b_7867 on
Hi; If I get the 'Trans Failsafe Prog" message twice within about 2 hours, The SES light will go on automatically. Since I do not seem to have any real transmission problems, this SES message clears itself in about 24 hours. The "Trans Failsafe Prog" messageseems to be used to indicate other transmission problems as well, like loss of transmission fluid, so be careful. I have a 2002 X5. Cheers. Omer
Posted on Nov 23, 2010
Could someone help me with a site I could use to down load a free owners manual, my car didnt come with one.
Check out this site for a free download.
Posted on Aug 13, 2009
I have recently bought a 2003 bmw 530 d with bmw i drive system install,the car has had after market tyres fitted and no longer has the run flat tyres on. Every time i start the car i have tyre puncture warning on the i drive screen and it wont turn off is it possible to reset this manually.
Posted by aarronbing... on
use the I drive system to reset flat tire monitor, go to vehicle settings, then flat tire monitor, then select reset, then you have to drive the car system resets as you drive
Posted on May 24, 2009
where is the alternator fuse on a 2001 bmw x5
Posted by Shiron... on
Check fuse number 5 and fuse number 15 in the glovebox.
For more help i suggest click the link below and follow the troubleshooting steps:
This will help.Thanks.
Posted on Jun 11, 2016
566 questions posted
Usually answered in minutes!
Step 2: Please assign your manual to a product: