20 Most Recent 2005 Mitsubishi Endeavor Questions & Answers

The idle air control is attached to the throttle body, located between the air cleaner and the intake manifold, and held on with 2 or 3 small screws. You should clean this, and the throttle body with carb cleaner while it is apart and try to resurrect.

2005 Mitsubishi... | Answered on Feb 14, 2020

Look at the fan radiator switch
Try unplug the CTS,if you see the radiator working continuously
Than the CTS, than change it

2005 Mitsubishi... | Answered on Feb 11, 2019

You probably need the window regulator replaced. Check with a parts store, you can probably get an aftermarket regulator. Dorman makes them.

2005 Mitsubishi... | Answered on Jan 09, 2018

Some times, it can be many causes
settings, gass scape from system,ac relay out of range
Anyway, read pressure of system high pressure, is good and low pressure is good too make vacuums to recommend psi put gass

2005 Mitsubishi... | Answered on Oct 18, 2017

If your parking brake is too loose or is not properly adjusted, you may encounter problems while parking, positioning and driving your car. Most of the time, car owners would send their car to a mechanic in order to fix and tighten the parking brake. However, you can actually skip this step and adjust your parking brake yourself. When your car starts to slip on a hill in its park position, you need to start tightening the parking brake.1 Remove the car's center console cover placed around your parking brake level inside your car. This is found between the seat of the driver and the front passenger.2 Use your wrench to turn its adjuster nut found at the end of your parking brake's cable rod. Loosen the adjuster nut with your wrench, while making sure that it does not come off at your parking brake cable rod's end.3 Raise your car rear wheels using your jack, and use your jack stands to support both its rear wheels.4 Pull up your parking brake handle up to two clicks or notches. Tighten your adjuster nut until you feel a slight resistance on your rear wheels whenever you spin them.5 Release your parking brake lever. Check and make sure that your rear wheels are still able to spin freely and without any resistance.6 Pull up on your parking brake lever up to three to five clicks or notches, while making sure that your car's rear wheels are not turning at all.7 Lower the car by adjusting your jack, and remove your jack stands from your car's rear wheels.

2005 Mitsubishi... | Answered on Sep 29, 2017

locking solenoid has failed, might be the wiring in the door or the motor its self has gone.

2005 Mitsubishi... | Answered on Jul 28, 2017

I'm don't known what's transfer caes
But, if you means transmission, sometimes when taking something out of levels,it will ties to others areas due weight
I'm don't know are you doing,if any heavy things use lifter and wiggle it.
(It a very basic idea ).

2005 Mitsubishi... | Answered on Jul 08, 2017

Usually threw the radio. Owners manual tells you. Manufacturer usually gives free downloads of manuals.

2005 Mitsubishi... | Answered on Sep 15, 2016

in the exhaust manifold of the front bank or before the cat converter
bank 2 is closest to the grill and bank one is next to the fire wall
the heated oxygen sensor is before the cat converter and the normal oxygen sensor is after the cat converter

2005 Mitsubishi... | Answered on Jun 19, 2016

on 2005 mitsubishi endeavor . srs is on . how do you turn it off or reset it

2005 Mitsubishi... | Answered on Feb 24, 2016

If it is only that window then not a fuse. Something is wrong with the window system. I have seen motors burn out in a short period of time. Could even be the switch

2005 Mitsubishi... | Answered on Dec 09, 2015

It is usually on the fuse box cover. If that's not readable look in owners manual under fuses and it should show you the correct amperage for each fuse and its place in the panel or box.

2005 Mitsubishi... | Answered on Dec 06, 2015

possibly switch or broken wire between door and pillar. frequent closing and opening of door causes wire/s to break or might be a defective power window motor.

2005 Mitsubishi... | Answered on Sep 11, 2015

turn key on wate a bit thean crank see if that help if so ck fule felter

2005 Mitsubishi... | Answered on Mar 03, 2015

Requires transmission removal for repair.

2005 Mitsubishi... | Answered on Feb 20, 2015

after connecting a new battery you sometimes have to use a scanner to reset the CPU program which includes the immobiliser system

2005 Mitsubishi... | Answered on Feb 12, 2015

Not finding what you are looking for?
2005 Mitsubishi Endeavor Logo

329 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Endeavor Mitsubishi

  • Endeavor Mitsubishi

Most Popular Question

window will not roll up passenger front

  • Cars & Trucks