2008 Mitsubishi Endeavor - Answered Questions & Fixed issues


The very first thing that you need to do is have the engine control computers fault codes checked. The idle speed is 100% computer controlled.

2008 Mitsubishi... | Answered on Jul 17, 2016 | 124 views


Tiene correa o banda tensora.

2008 Mitsubishi... | Answered on Oct 20, 2015 | 251 views


Can you reach from back.

2008 Mitsubishi... | Answered on Aug 23, 2015 | 141 views


Remove belt and spin each pulley to check for smoothness or noise.

2008 Mitsubishi... | Answered on Aug 04, 2015 | 443 views


Try to reprogram key by turn key on and off 3 to 4 times and try again

2008 Mitsubishi... | Answered on Aug 02, 2015 | 133 views


It is under the driver's kick panel. Occasionally, they are under the passenger's kick panel. (Remember, the Japanese drive from the right-hand side and some car designs are not switched over completely for our LHD in NAFTA countries and Continental Europe.) The socket has 21 pins on it as I remember.

2008 Mitsubishi... | Answered on Mar 21, 2015 | 70 views


Sounds like you have a weak battery..try giving it a good charge and try again many times engines will not start with a battery that turns the engine over but not fast enough to start.. Good luck.

2008 Mitsubishi... | Answered on Nov 12, 2014 | 257 views


I have a 2008 Mitsubishi Endeavor. My son put coins on the lighter and after he put them inside i couldn't use it anymore. I don't know where is the fuse panel at?

2008 Mitsubishi... | Answered on Aug 12, 2014 | 1,868 views


is it electric ? if so check the fuse , the switch if both ok then i suspect it is the window actuator /motor assembly

2008 Mitsubishi... | Answered on Jul 04, 2014 | 59 views


2008?
does car run? and move?
is the Check engine lamp glowing , moving?
yes, and you scanned it and got just ONE DTC?
P0551, (which engine option do you have?)
that code is power steering fail.
check fuses first
use a scan tool to reset the errors
test drive car see if it returns.
same answer any car.
if comes back ,
the sensor is bad,
or its wires fell off.
or you are turning the steering real hard in to a curb and overloaded it.
in the later case, stop that, or we tell you mum.

2008 Mitsubishi... | Answered on Jun 17, 2014 | 103 views


Does it do it with the A/C too?? If so it could be a broken fan wheel in the blower.. or a piece of trash in the blower housing.. like a leaf.. Post a comment so we know what you find..

2008 Mitsubishi... | Answered on May 23, 2014 | 157 views


Its either a bad blower motor or a bad speed resistor pack that controls the fan speeds.

2008 Mitsubishi... | Answered on Mar 18, 2014 | 72 views


Have you considered checking for codes,
seeing as how you have a Diagnostic
Check Light on?

2008 Mitsubishi... | Answered on Mar 13, 2011 | 222 views


The oil filter is underneath the engine passenger side, at the back of the air conditioning compressor
&&
The oil drain plug is under the passenger side of the engine, it is on the posterior-inferior portion of the oil pan.



Hope this helps

Positive Feedback ALWAYS welcome :)

2008 Mitsubishi... | Answered on Mar 03, 2011 | 176 views


multicylinder misfire--get it on a tech II scanner and have a data stream read to pinpoint--look under hood for any flaws-think tuneup

2008 Mitsubishi... | Answered on Feb 19, 2011 | 92 views


Please see my tip at http://www.fixya.com/cars/r5932051-check_engine_light_check. These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

2008 Mitsubishi... | Answered on Dec 21, 2010 | 202 views


these vehicles have a senser right in the wheel bearing (hub) the only way to fix the problem is to change the hub.when the brake light comes on it disables the traction control and that is why that light comes on a the same time.

2008 Mitsubishi... | Answered on Dec 09, 2010 | 347 views


abs senser in back of rotor couple of screws a plug and a new senser

2008 Mitsubishi... | Answered on Sep 30, 2010 | 134 views


hi this maybe due to the brake switch being either stuck in or the switch itself has broken, if you look under your dashboard where the brake peddle is, you should see a black or white plastic thing being held to a small bracket, there should be a little plunger sticking out, if not, unplug the switch ( should be a 2 wire plug ) then undo the nut holding it in the bracket, and have a look and see if the plunger is broken or just stuck in, it could have some dirt holding it in place, just pull it back out and lubricate with a light oil, obviously if it is broken just purchase a new one....hope this helps please vote thanks

2008 Mitsubishi... | Answered on Jul 28, 2010 | 1,352 views

Not finding what you are looking for?
Cars & Trucks Logo

72 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...