2008 Mazda B Series Pickup - Answered Questions & Fixed issues
What does code 6-4 mean
Bank 2, sensor 3 is having a high reading. This would be the last sensor after the Catalytic converters. Also have the Code erased by going to Autozone, Oreilys, or Advance autoparts and getting the free scan.These parts places can sell you the correct part. You will also need a special socket to remove and replace the part.
12/17/2011 2:23:55 PM •
2008 Mazda B...
•
Answered
on Dec 17, 2011
•
137 views
I have a 2008 mazda
Check the fluid level and make sure it isn't low. You'll also want to check the main vacuum line that connects to the brake booster for leaks.
5/4/2011 7:53:21 AM •
2008 Mazda B...
•
Answered
on May 04, 2011
•
420 views
How do you reset the computer on a 09 mazda bt50
Today's ECU's have some pretty awesome abilities.
Many years ago before computers controlled cars, you had literally heaps
and heaps of adjustable areas under the engine to get the engine tuned
and running sweet, set the fuel mixtures, timing, clearnes for BTDC,
etc.
These days the engine has sensors all through the engine to see what is
happening and report back to the computer, and based on this information
the computer responds with instructions to control the engine and keep
it running how it 'believes' it should run based on the information
received from the calibrated snesors located in the system.
There are several key-sensors in the system that the ECU learns from, including crank angle sensor, o2 sensor, and knock sensor.
After a while, the calibration of the sensors becomes scewed slightly from wear, from pollution and dirt, etc.
Performing an ECU reset usually means that the computer goes back to
factory rom settings, which are fail-safe levels, and then it quickly
learns from the readings it gets back, comparisons to what it thinks it
should see and what it really is seeing, then it adjusts and re-compares
again.
On most cars and ECU reset will se increased fuel consumption for the
first 15 - 30km's, but then levels back to normal, and on some cars you
can get better consumption after the level off period.
After my speal above... take the negative lead off the battrey for 30mins
10/7/2010 11:04:41 AM •
2008 Mazda B...
•
Answered
on Oct 07, 2010
•
3,624 views
Half the dash lights are out on my mazda b2500
There are several small screws to remove. It doesn't take long once you've done it and know where they are located. First you must remove the center console--there are two screws (i think 7mm or 8mm) underneath the middle part kind of hidden from view on the center console. Then remove the lower plastic panel under the steering wheel. Then a metal panel must be at least loosened enough to reach the lower screws on the dash panel you're trying to get at. Then there are three more screws along the top ledge that must be removed. Then you can get to the bulbs. I think there are 5 in there, and two in the center console. It sounds difficult and time consuming, but it only took me like 15 minutes start to finish
9/7/2010 1:17:00 PM •
2008 Mazda B...
•
Answered
on Sep 07, 2010
•
1,851 views
We have a problem with excessive vibration at
95% of the time a vibration at that speed, while cruising,(not braking or heavy acceleration) is from the tire/wheel assembly. What that means is ASSUMING the balance is done correctly...then..are the tires round?(generally no more than 60 thousands of an inch of lateral or radial runout) Are the wheels bent? I am ASSUMING the front end is tight. Finally, by weird chance you have a nylon belted tire from the old days it will shake until it warms up. That's an old brain cell! Oh, if you are getting "wheel hop", not vibration, then you have weak shocks/struts
9/25/2009 10:32:25 PM •
2008 Mazda B...
•
Answered
on Sep 25, 2009
•
263 views
Tow Hook
there hook is on the frame rails on each side/ Please rate my response thank you very much
2/1/2009 9:26:56 PM •
2008 Mazda B...
•
Answered
on Feb 01, 2009
•
120 views
What size engine do i have
the 88 B series engine is 1.8L, the reason it shows 1.6 and 1.8 is because they are the same eng block series, just like a chevy small block V8 comes in 5.0L, 5.7L and 6.6L but all are the same basic block.
1/21/2009 10:39:34 PM •
2008 Mazda B...
•
Answered
on Jan 21, 2009
•
122 views
Mazda BT 50 3.0L injector problems
i don't think there is any problem with injectors but the cause could be pump
just loosen the pump bolts a little bit so that you can move the pump with leverage to advance
check the heater plugs as well
12/27/2008 6:08:23 PM •
2008 Mazda B...
•
Answered
on Dec 27, 2008
•
3,980 views
My 1998 Mazda b2500 won't
with a manual tranny, the most likely cause for problems going into gear is the synchronizers, as long as it is just the synchros, a rebuild on bearings and synchros is not to terrible.
I have an 86t b2000
The choke wire plugs into the back of the alternator. Did you put the head back on with the engine at TDC? Have you checked the ignition timing?
I have just rebuilt a
how are you priming the system
before installing the oil pump , you fill it with grease or vaseline
That primes the pump so that when you start cranking it it is producing pressure
to get pressure you need volume and there will be no way that you will get the volume required other than by the pump
Not finding what you are looking for?