20 Most Recent 2008 Nissan Versa Questions & Answers

Usually pretty easy apart from the fact you are doing it under the vehicle. From ones I have done. Undo the hydraulic pipe, undo the bolts on the slave cylinder and remove it. Bolt the new one in place, reconnect the pipe and then bleed the air out. https://www.google.com/search?q=2008+%22nissan+versa%22+%22clutch+slave%22+cylinder+replacement It will be the same as these videos irrespective of make and model

If fuses are OK, as in, did you put meter on them, or just look, for sometimes you can't see if fuse is bad, many times a fuse looks good but is not, so meter is only way to make sure, or switch fuse with another of same amp and color. A relay in many cases is used for wipers and if you have delayed headlight option, this too is using a relay, so relays just pull straight up and out. A chart should be in each fuse panel, so again, if relay, you can switch with another since most vehicles have more than one, and with same part number, this will narrow down problem and avoid wasting money on new relay which is expensive in comparison to fuse. Good Luck, FREE-BUSINESSES.com

the deflector flap that move to direct air flow is stuck under the dash.

You will almost definitely have to remove the inner door trim etc to access the rods etc that work the lock. Try youtube.

images for 2008 Nissan Versa Removing tensioner

how do you remove tension off surpentine belt tensioner - Nissan Forum

www.nissanforums.com/.../151350-how-do-you-remove-tension-off.htm...
Feb 20, 2009 - 4 posts - ‎2 authors 2008+ Nissan Rogue ... QR25 2.5L Engine Engine Discussion: 2002+ Sentra SE-R and SpecV ... how do you remove tension off surpentine belt tensioner ... changed these before, but which way do you turn the tensioner, how ... Replacing the Water Pump on a '04-'08 Maxima *DIY* 1 post Aug 31, 2011 Belt noise: replace idler pulley? - GA16DE 8 posts Sep 16, 2008 Step by step instructions -Upper Timing Chain Tensioner 15 posts Dec 8, 2007 Idler Pulley Bearing Replacement Info 5 posts May 16, 2003 More results from www.nissanforums.com

Nissan Versa Tensioner Pulley Issue (1/1) - EricTheCarGuy ...

www.ericthecarguy.com/.../50669-nissan-versa-tensioner-pulley-issue
Nissan Versa Tensioner Pulley Issue 1 year 7 months ago #94552 ... for a 50 Torx to be used to remove the entire tensioner pulley assembly but all of my 50Trx

How to Replace serpentine belt 2008 Nissan Altima ...

? 11:29 https://www.youtube.com/watch?v=5NchA85pnAE Jul 2, 2014 - Uploaded by nivekoch How to Replace serpentine belt 2008 Nissan Altima In this video i'll be going ... 2005 Nissan Altima 2.5L serpentine belt tensionerreplacement ...

go to www.youtube.com how to bleed the brakes www.wikipedia.org ask the same questions but i think the video is easier

Check all vacuum hoses, a large vac leak will do this.

Timing chain.

You have a stoplight switch that is connected to your brake pedal,get a flashlight and push brake pedal in by hand and see if switch is engaging,if not,then you can adjust,if engaging,then switch may be bad.

MUCH more likely, Wendy, is that the horn has burned out (they do that) or the horn button inside the steering wheel has stopped working because of corrosion (they do that, too). It's HIGHLY unlikely that any wire anywhere has been broken. It's POSSIBLE that the plug at either the horn or the horn button has come loose, though - that's a thirty-second no-parts repair at the horn, or a ten-minute no-parts repair at the button.

No answer here. Looks like you have to remove the intake manifold (5- 10mm bolts in front, on the rear at the throttle body, it looks like connect from air intake snorkel, remove snorkel and take out the bolt on the other side to get to the plugs. This POS site tells you nothing useful.

Manifold vacuum leak,valve held open,if it has hydraulic lifters let it run for a while ,then check compression