20 Most Recent 2008 Nissan Pathfinder - Page 6 Questions & Answers

change the oil for the 5th time and rotate tires

check the rubber insert between the spring and mounting pad,

you can buy at any parts store and most will install them, but if not left twist the bulb or unscrew the backing plate then without touching the bulb plug it in and reinsatll.

Let them realign it and tell them to have a check on your Hubs.

Don't forget to rate this

P259A Engine Code Repair - P259A OBD-II Diagnostic ...

enginecoderepair.com http://p259a.enginecoderepair.com The reason of P259A OBD-II Engine Trouble Code is O2 Sensor Heater Circuit Malfunction. P259A DTC reports a sensor fault, replacement of the sensor is unlikely ... ..

car starts and runs ok, dash heater blower heater works on high and head lamps all work? pad means keyfob or door control buttons? on door inside? check all fuses first. as in ALL (cab and engine bay) if fuses good scan the PCM for door control errors DTC all 4 doors fail at all local control (windows and locks) ?????????

Wiring Harness https://www.google.com/search?q=2003+Nissan+Pathfinder+SE.+wiring+harness+for+the+Bose+Factory+Stereo The wiring diagram is here, but no Pink! https://www.carxtc.com/Nissan-PATHFINDER-SE-03-2003-FACTORY-Car-Stereo-Wiring-installation-Harness-OEM-Radio-install-wire_p_39138.html https://www.google.com/search?q=2003+nissan+pathfinder+se.+bose+factory+stereo+wiring+diagram ..

snow plowing? blade down? we cant see what your doing in snow or where. but learn to scan the PCm any time the transmission messes up what does CUT OUT mean, elaborate that. means engine stalls or tranmission FLARES? RPM go super high.? 4wd High, (center locker locked if has that)? 2 things can cut engine or trans even the TC can mess up. pin that down and we have a party.

If you are going to scrap it, you can use the fuel pump in the tank itself. If it has a leak, use a manual or battery operated fuel transfer pump through the filler. https://www.google.com/search?q=fuel+transfer+pump ..

Hello. It seems your Nissan's alternator stopped recharging; causing your Pathfinder to run on battery. The battery became discharged not to 'power' the starter yet light the lights. Recharge your car's battery then start your car. Good luck and keep me informed; if you want to.

You can't , best bet call a mobile lock smith . He'll cut you a new key and program it .

Hi Eduardo:
Check this information (click over pics for zoom)...



Fig. 20: Exploded view of the cylinder head assembly-VG30E engine




Fig. 15: Cylinder head loosening sequence-VG30i and VG30E engines




Fig. 17: Cylinder head torque sequence-VG30i and VG30E engines


Install the cylinder head with a new gasket. Apply clean engine oil to the bolt threads and seats, then install the bolts with washers (beveled edges up) in the correct position. Note that bolts 4, 5, 12 and 13 measure 5.00 in. (127mm), and are longer than the others. The other bolts are 4.17 in. (106mm) long.

Tighten the bolts in the proper sequence, in the following stages:
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 43 ft. lbs. (59 Nm).
Loosen all bolts completely.
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 40-47 ft. lbs. (54-64 Nm). Or, if you have an angle torque wrench available, tighten them an additional 60-65 degrees.


Hope this helps; remember to rate this answer. Good luck.

Videos of belt changes here..... Enter your question into Youtube.com search bar and see what comes up. Regards Geoff

you can try out some guide from here reliable-store they also provide live chat feature for instant help and it's very useful

So which is it- it wont turn over OR it sputters when cranking like it wants to start?

Check your wires for good connections.

https://www.youtube.com/watch?v=DH7fEcm-HUI Please refer to the above video.

To be safe, go to a parts store and most will check the codes for free. Then you will know.