2007 Dodge Caliber SXT Sport Hatchback - Answered Questions & Fixed issues
2007 Dodge Caliber
Make sure you have a fully charged battery. When starting the car, push the gas pedal down to the floor to engage the choke. Then push pedal halfway down and turn the ignition. Try jump starting to see if it is the battery. If it still turns slow it may be a bad starter.
1/21/2023 7:42:47 PM •
2007 Dodge...
•
Answered
on Jan 21, 2023
•
538 views
Rough idle
What about the coil packs? Do you have a check engine light on? If so take it to an auto parts store and see if they will scan your vehicle for the codes.
10/11/2022 5:35:37 PM •
2007 Dodge...
•
Answered
on Oct 11, 2022
•
460 views
Gear shifter is stuck on
PERMANENT FIX that doesn't cost a dime or require any tools. It happened to me by accident. Break the detante by moving the gear selector while holding the manual override lever (plastic lever inside the access hole). Once it is gone no matter what the brake switch calls for (lock gear selector or not) the gear selector will always be movable because the mechanical locking mechanism is no longer there. TADA!!! So what if you no longer have to depress the brake pedal in order to change gears. Call it a retro fix.....!
11/11/2021 8:02:51 PM •
2007 Dodge...
•
Answered
on Nov 11, 2021
•
6,203 views
2007 dodge caliber etc light on
Get a can or two of carb & choke or intake cleaner. Take the intake boot off at the throttle, and clean it thoroughly. It miught help to use a small brush (like an old toothbrush) or some paper towels to help wip it out
6/14/2021 8:50:45 AM •
2007 Dodge...
•
Answered
on Jun 14, 2021
•
816 views
9ATE
It maybe saying "gate". which means the rear hatch is either not shut fully or there is a prob with the switch in the latch
5/3/2020 11:13:19 PM •
2007 Dodge...
•
Answered
on May 03, 2020
•
4,430 views
How to reset tire pressure monitor on a 2007 dodge caliber SXT
You need to drive for the new sensor to program into the WCM unless it's a after market sensor then sometimes the system will not recognize it.OE sensor would have to be installed then.If you have dashes where the tire pressure would be then this would be normal til the system see's a good sensor.Otherwise the Chrysler scanner could program the sensor # into WCM or WIN
11/24/2019 9:12:25 PM •
2007 Dodge...
•
Answered
on Nov 24, 2019
•
990 views
I thought my headlights on
There are separate fuses for each light. High and low. Located (usually) in the power center under the hood. Check the fuses.
12/29/2017 6:07:01 AM •
2007 Dodge...
•
Answered
on Dec 29, 2017
•
228 views
Losing fuel mileage per gallon
injectors not operating properly , dirty fuel or leaking injector seal/s
heated oxygen sensor(HO2S ) in the exhaust manifolds not reporting the gas composition correctly to the ECM and running it rich or loosing control
run the fault codes to find the problem sensor
6/26/2017 10:13:17 AM •
2007 Dodge...
•
Answered
on Jun 26, 2017
•
178 views
Blower Motor Grounding Point
My diagram is showing that the ground goes through the instrument cluster not G200. If you unplug connector 2 at the heater control there should be power on the first 4 wires with the key on. The 5th wire is the G200 ground. If there is power plug it back in and see if there is power at the blue with pink wire on connector 1 with the connector plugged in. If there is power there than there is an issue with that wire or in the cluster. it is also possible that the TIPM or the cluster detected a problem with the HVAC and decided to shut it down. You would need a scan tool to see if this is the case. I’m happy to assist further over the phone at
https://www.6ya.com/expert/jeremy_d728a59f986299fa
10/6/2016 3:07:43 AM •
2007 Dodge...
•
Answered
on Oct 06, 2016
•
163 views
Not finding what you are looking for?