20 Most Recent 2004 Nissan Nissan almera tino - Page 7 Questions & Answers

It could be numerous problems - consult a reputable shop - you need someone that knows what they are talking about to physically look at the car to solve the problem - will save you a lot of time and expense. ????

Probably the fan got blocked with some debris and caused it to draw too much power, that caused the fan controller to fail. Or, the fan controller has failed, has a bad connection etc. Check the cabin filter if it has one, for a blockage.

Hello, Malcolm. It seems like you are facing an issue with the alarm system of your Nissan Primera P12 from 2002. Based on the symptoms you've described, it does sound like there might be a fault with the alarm system or the central locking mechanism. Given that you have already tried a few troubleshooting steps such as disconnecting the battery and replacing the micro switches, it might be a good idea to further investigate the alarm system itself. Since the hazard lights are flashing without any audible alarm sound and the central locking is behaving inconsistently, there could be a fault in the alarm control unit or wiring. One possible cause could be a faulty alarm module or a loose connection in the wiring harness related to the alarm system. It's also worth checking the condition of the alarm siren to ensure it is functioning properly. Considering that the issue seems to have improved after disconnecting and reconnecting the battery, it's possible that there is an intermittent fault related to the power supply or a reset of the alarm system. If the problem persists, it might be best to consult with a professional mechanic or an auto electrician who can perform a more in-depth diagnostic test on the alarm system to pinpoint the exact cause of the issue. In the meantime, if you experience the hazard lights flashing again, try to document when and under what circumstances it occurs. This information can be helpful in diagnosing the problem more accurately. I hope this information helps, and I wish you the best of luck in resolving the issue with your Nissan Primera P12. Feel free to reach out if you need further assistance or have any more questions.

To remove the starter motor on a 1994 Nissan Bluebird SSS 2 litre ATTESA-U13 engine (AWD), follow these steps: 1. Disconnect the negative terminal of the battery to prevent any electrical accidents. 2. Locate the starter motor, which is typically located near the transmission bell housing on the engine block. 3. Remove any heat shields or other components that may obstruct access to the starter motor. 4. Disconnect the electrical connections to the starter motor, including the wiring harness and solenoid. 5. Remove the mounting bolts that secure the starter motor to the engine block. 6. Carefully slide the starter motor out of its mounting position and set it aside. 7. Install the new starter motor by reversing the removal steps. As for finding a repair manual for your Nissan Bluebird SSS, you can try searching online for a digital version that you can download, or you can purchase a physical copy from a reputable auto parts store or online retailer. Additionally, you may also be able to find helpful information and step-by-step guides on online forums and websites dedicated to Nissan vehicles.

Has the Throttle body been removed and cleaned thoroughly both sides? Was a Throttle body relearn done afterwards. https://www.google.com/search?q=2018+Nissan+NP200+8v.+Throttle+body+problem Ideally you need an auto electrician to check for Diagnostic Trouble Codes and do a full system scan with a pro grade scan tool computer. It can also do the relearn and check the IAC. https://www.google.com/search?q=auto+electrician+near+me ....

Question edited and turned around for clarity. Not enough coolant in the heater core. Have a read and follow these instructions carefully. https://www.fixya.com/support/r29872074-vehicle_cooling_system_no_heat They do have some 'history'. https://www.google.com/search?q=1996+Nissan+Largo+no+heat ..

Is this electronic throttle control ? Try cleaning the throttle plate with some carburetor cleaner , they can get dirty an cause this problem . Are any lights lit on your dash , check engine , ETC , ? This is a 2011 ? Still under warranty , take to the dealer !!!!

Is this a new key as well? On a lot of modern vehicles the vehicle's electronics need to be told that there is a new ignition key and ignition barrel fitted. This will need to be done through the OBD connector under the dashboard. If it is not done the vehicle immobiliser won't turn off as it doesn't recognise the key you are using.

You will probably have to reset the ECU as it thinks the vehicle may be stolen and shuts the fuel supply off. I always plug a motorbike battery with a cigar lighter plug on it, to keep the electronics live whist changing the battery. It keeps 12volts on the system and avoids this sort of thing from happening.

I would check the heaters are working on the down stream sensor and ensure they are supplied and manufactured by Nissa.

Taking out the steering box in a Nissan 1400 2007 pickup truck involves a few steps, and you do not need to remove the engine to access the steering box. Here is a general guide on how to remove the steering box:
1. **Disconnect the battery**: Always disconnect the battery before working on any components in the engine bay.
2. **Raise the front of the vehicle**: Use a jack to lift the front of the vehicle and secure it with jack stands for safety.
3. **Remove the wheels**: Take off the front wheels to access the steering components.
4. **Disconnect the steering column**: Inside the cabin, detach the steering column from the steering box.
5. **Disconnect the tie rod ends**: Remove the tie rod ends connected to the steering box.
6. **Remove the steering box mounting bolts**: Locate and remove the mounting bolts that hold the steering box in place

This says it needs a programming computer, so Auto-electrician, Auto-Locksmith or dealership.

2019 Nissan Rogue Keyless Entry Remote Fob Smart Key ...

programyourremote.com https://www.programyourremote.com > classified > 2019... Step by Step How to Programming Instructions: This vehicle is not on board programmable and requires a qualified professional to program smart key remote fobs. https://www.google.com/search?q=2019+Nissan+Rogue.+Key+fob+programming ..

https://www.justanswer.com/nissan/jzqy5-replaced-valve-body-no-reverse-its-hot.html

Sounds like the motor bearings are shot - you will need to replace it.

Is the security light lit up on the dash at all?What happens if you try to start the vehicle without unlocking the driver door with the key?Lastly, have you ever replaced the battery on your key fob? When their batteries get low, they can cause various problems that resemble mechanical faults or security problems.

If the battery is OK the next thing to check is the starter motor itself. It usually shows as a single click or lots of fast clicks? For the overheating, how long after you start the engine does it start to overheat? If it takes a while, usually as the engine starts to get up to working temperature, the first thing to check is the thermostat. This is the most common thing to fail especially on higher mileage engines. Do this first as it's the cheapest fix. Next check the serpentine/Auxillary belt. A worn or damaged belt can slip slowing the pump down. This can also show as battery charging issues. Another cause of overheating is the waterpump failing. This can commonly be heard as a whine, chirp, or a squealing noise especially on a cold start. It can also often, but not always, be see below the pump as staining from it leaking.

Disabling a car alarm yourself can be tricky and might vary depending on the exact model year of your NP200. It's actually not recommended for safety reasons. Here's a safer route: contacting a Nissan dealership or a trusted mechanic. They'll have the proper tools and knowledge to handle your immobilizer issue and get you back on the road securely.

Help in the link. I like to use a broader approach. Google year nissan model A14 mains and big end torque settings https://www.google.com/search?q=Torque+settings+for+nissan+A14+mains+and+big+end+bearings ..

There is no relay for the dash indicators. I'm assuming you're referring to the dashboard's instrument panel. There's a 10amp fuse for the instrument panel that you should check and/or replace. It's in location F11 of the fuse box, located in the vehicle on the driver's side. https://fuse-box.info/nissan/nissan-navara-d22-1997-2004-fuses-and-relay

Hi I'm driving np 200 Is no start I'm keep on making on and of on and off but started after 1 minutes, please help me What It can be problem .