20 Most Recent
2007 Toyota Hilux 2.7 - Page 5 Questions & Answers
Where is the blend door actuator on my 2012 hilux RHDrive.
HVAC + blower assembly (above drawing is LHD ONLY) no RHD here in USA (mail man excepted)I'd say off hand MIX motor actuator is lower right USA, LHD, and lower left in British Crown colonies. etc. RHD. this beast on ours will never ever fit in yours and will be a reverse image I bet. (look yet?)_the factory service manual covers all that. for sure.this RHD car go to your dealers web site toyota. and pretend to buy that partand behold a 3D drawing just like mine above. showing the parts to buy on that assembly.end RHD. story told by yanks.(Rebel actual), I buy the book with the car, then never have to beg for this.
Does anyone know why my ignition fuse blows?
I suspect the fuel concern is a diagnostic dead end. This sounds like an electrical short. However, at the third key position, the glow plugs are also activated. Glow plugs use relatively high current flow to energize. On my older hilux, they are on a separate fuse under the hood. If they are shorting on the glow plug rail to a loose wire or any other grounded item, the fuse will blow. You will have to check if yours are on a separate fuse, as well. Regardless, I would first check your ignition circuit by obtaining a wiring diagram and tracing the wires from the ignition to the next element in the circuit. From there, to the ECU and from there to the starter solenoid.http://landrover.narod.ru/gershon/TOYOTA/HILUX/Toyota_Tiger_1KZ_2001.pdf
How do I remove the coin tray from my sr5toyota hilux
My '04 Toyota Hilux cup holder came out as follows...
You need to start by removing the dash trim that surrounds the instrument panel and air vents, as per the following.
Looking through the steering wheel to the instrument panel, remove the two screws above the instrument panel window.
Then remove the two screws under the steering column.
Then carefully prise back the section of lower trim to the right of the radio, you will see another screw, remove this.
The instrument trim is now free to be wiggled free from its clips.
You will need to disconnect the lead to the digital clock.
You can now remove the whole dash trim which contains the housing for the cup holder and place it on a work bench.
If you then look down onto the sliding tray (from above) you will see two squareish tabs. These tabs are the limiting tabs preventing the tray from sliding out (under normal use).
What you need to do is slide the tray out wards and using a flat screwdriver lever these tabs downwards as you pull gently on the tray. You should do one side at a time, so push one tab down until the draw is free on that side then while holding the draw steady repeat for the next tab. Once the two tabs are squeezed free the tray will slide out.
With practice I suppose you could just pull the tray straight out (without removing the dash trim) by interting two hacksaw blades curved slightly upwards throught the front of the (open) tray to squeeze the tabs as you pull the draw forward but you need a little luck and knowledge of where the tabs are... And besides, removing the dash trim is pretty simple.
With these instruction it should take no more than 10-15 minutes start to finish.
Good luck!!
Mike
Hilux. Where is the petrol cut off switch?
You don't give a year or model so I will cover both ,carburetor model no cut off switch, mechanical pump sucks fuel from the tank and delivers under pressure controlled by the float needle and seat to the carburetor . fuel injection no mechanical cut off switch pump is powered from the ignition switch via a relay, the ECU will switch off the fuel pump when the required pressure is reached .
2.0l engine. Why doesn't it accelerate?
Too many things to list. Get it on an expensive scan computer and look at the live data.
Look at the Scotty Kilmer YouTube channel and in search put scan tool.
First things to do would be clean MAF and Throttle Body.
How to set timing for toyota Hilux 2y engine
Follow these steps:
1. Loosen off the distributor coil.
2. Connect the timing light lead clip to cylinder marked as number 1 cylinder spark plug lead.
3. Connect the red wire clip to the positive battery terminal
4. Connect the black clip wire to the negative battery terminal.
5. Put the gearbox is in neutral, and pull the hand brake
6. Start the engine
7. Turn the throttle knob until the engine is revving at 600rpm
8. Check the crank pulley, and look for the crank pulley mark, if the mark is not visible switch off the engine.
For a step by step guide, follow this link: https://www.autozone.com/repairguides/Toyota-Cressida-and-Van-1983-1990/Firing-Orders/Ignition-Timing/_/P-0900c1528008141e
Not finding what you are looking for?