20 Most Recent 2006 Peugeot 207 1.6 Questions & Answers

0helpful
2answers

How do I remove the bonnet of my Peugeot 207?

needs 3 people one to hold the bonnet up and one on each side to undo the hinge bolts and gas struts if used replacement is reverse with an adjustment before the bolts are properly tightened about 10 minutes work
6/30/2017 3:54:40 AM • 2006 Peugeot 207... • Answered on Jun 30, 2017
0helpful
1answer

Engine temp guage reading hot but engine cold. new temp sensor and thermostat has been fitted

temp sensor on engine check that has wire on it in the manifold
4/20/2016 6:30:59 AM • 2006 Peugeot 207... • Answered on Apr 20, 2016
0helpful
1answer

My temp gauge rises in idle but then when driving falls to bottom

Thermostat stuck open likely.
6/21/2015 8:58:59 PM • 2006 Peugeot 207... • Answered on Jun 21, 2015
0helpful
1answer

Ac compressor relay location

If you suspect low refrigerant you can use paperclip to jumper the low pressure switch momentarily. Relay should be in main fuse block under the hood, I think.
6/12/2015 6:35:22 PM • 2006 Peugeot 207... • Answered on Jun 12, 2015
0helpful
1answer

Which fuse for Warning buzzer on 2006 Peugeot 207

Go and check the rear left and right tail lights. take off connector and you'll notice that earth wire and pin is blown.
4/8/2015 7:28:39 PM • 2006 Peugeot 207... • Answered on Apr 08, 2015
0answers
0helpful
1answer

Clutch pedal goes to floor

Hi Stephen, I think the problem is a leakage from either the clutch master or slave cylinder. Open the hood and check the fluid level in the clutch reservoir. If it's empty my suspicion is confirmed. Look for signs of leakage first from the master cylinder, then the pipes and finally the slave cylinder. It's a good idea to replace both cylinders at the same time. To do so requires the following work. Inside the cabin the push rod connecting the pedal to the piston must be disconnected and then under the hood (bonnet) the fluid pipe disconnected followed by removal of the securing bolts. The same operation applies to the slave cylinder. When assembling always connect the pipes before securing the cylinders.Hand tighten the pipe connections, leaving just one final turn for the wrench (spanner). The pipe connectors are easily damaged by cross threading the connectors which results in leakage. Once the clutch operating system has been installed, fill the reservoir and have someone kind keep it full with dot 4 brake fluid. Open the slave cylinder bleed nipple and allow the fluid to flow into a container until the it flows without air bubbles and then close the nipple. Happy driving Regards John
10/27/2013 8:02:09 AM • 2006 Peugeot 207... • Answered on Oct 27, 2013
0helpful
2answers

When i unlock my vehicle the side mirrors does not open, can anyone please tell me what to do.

get inside the car turn the ignition on look at the electronic controls that operate the mirrors where you select left and right mirrors and just pull it backwards, It had me stumped for a while a quick look at the owners manual made it all clear (207 GTI) hope it helps
10/11/2012 3:04:37 PM • 2006 Peugeot 207... • Answered on Oct 11, 2012
0answers
Not finding what you are looking for?
2006 Peugeot 207 1.6 Logo

29 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Peugeot Experts

xxxxxx xxx

Level 3 Expert

5117 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

207 Peugeot

  • 207 Peugeot

Most Popular Question

temp gauge rises in idle but when

  • Cars & Trucks
Loading...