20 Most Recent
2005 Nissan Murano SE Questions & Answers
Windshield wipers not working but motor is running.
If wipers arms are not moving and motor operates, look at base of wiper arms. There will be a cover concealing a nut on each arm. Check and make sure the nuts are tight. If tight, suspect wiper transmission disconnected from wiper motor assembly and cowling will need disassembly for inspection/repair
Driving noise, not from bearings
it could be center bearing, if its going bad it can also cause a vibration, make sure you have sufficient fluid in the diff as well, you can also get a noise and vibration from collapsed motor or trans mounts
Is it ok to replaced rear Rotors with out replacing break pads?
OK if they are smooth and thick. It's not dangerous; it doesn't cause uneven braking, but I wouldn't advise putting very ridged pads back in - as they will tend to accelerate the wear on the disc/rotor. You CAN take the worst of the ridges out with a file, if you can use a file accurately and don't taper the pad... Don't use emery paper as some abrasive will remain in the pad and wear the disc/rotor. Also if the pads are very worn down, they will wear away quicker and could damage your new disc/rotor.
Does the 2005 Nissan Murano SE have rear window washer?
Yes it does and the washer fluid reservoir under the hood is for both the front and rear. The following is a diagram of the washer pump and hoses so you can check for operation or leaks.http://www.nissanmurano.org/forums/attachments/problems/15059d1233342517-rear-washer-fluid-not-squirting-washer-motor.jpg
Tengo el codigo P0456 y
Tengo un honda civic 2013 empieza a salir primero la luz del tampon de la gasolina luego la del check le cambie el vapor ganister purg,EGR valve solenois y el tapon de la gasolina pero no es el original fue remplazo y me da el codigo P0456 de una peque?a fuga..Que podria ser?
My nissan murano 2008 station wagon still locked after engine is off
all that is DIY programmable, per your users guide(in glove box)
and if battery main went dead it sure can forget all that.!
and goes to factory default settings . ( by design)
car starts and runs ok
key fob batteries all new. and fresh.?
I have all that in our cars turned off, I like being in control.
auto locks and unlocks are programmable in my key fob chapter of my users guide, like most cars are. (or configurable)
no told at all what else works great , like driving and head lamps etc.
cars have like 50 fuse and 50 feature now, do some work?
What's the torque for all four caliper mounting bolts behind dust plate and axle/wheel bearing/CV nut?
Assuming your Nissan is a 2016 or newer, the four mount bolts are 65ft/lbs, (88Nm).
For the 'CV' nut do you mean the large nut on the end of the drive shaft? That nut is tightened to 135ft/lbs, (182Nm).
This is a very tight setting so you will probably need to 'wedge' the brake disc to stop it turning as you tighten it. Try fitting two wheel studs next to each other and fully tighten them. Get a helper to hold a pry bar between the studs as you tighten the nut.
2007 Nissan Murano, cranks but wont turn over can't figure it out
If the engine sounds as if it wants to start, it is possible that you just have too much gas in the manifolds or in the cylinders. Try the following: Turn on the ignition but do not start. Hold down the gas pedal for a minute or two. Then start the car without releasing the pedal. I know some will say this method will not work with "drive by wire" systems such as MO's but I think it will.
More than likely though, the problem could be the anti theft system interfering, or locking down the ignition. Close all doors and then using your key (not the fob) lock and unlock the doors several times and then try.
Not finding what you are looking for?