20 Most Recent 2009 Nissan Frontier Crew Questions & Answers

check your wires and make sure you have a good clean ground. did you do a fuel pressure test after the r&r fuel pump

Im not aware of any adjustment on a power steering pump other than the tightness of the belt. There will be at least one bolt that the pump rotates on, and one that holds it in place. However, I would have to know the year, make, model etc...Some have no adjustment and belt it kept tight by a tensioner pulley. Look for a bolt that has a slot that it slides in, loosen all bolts until pump is loose and have an assistant carefully keep pressure on it with a thick broomhandle, giant screwdriver, or prybar. Most belts are set to about 1 inch of play.

It has an automatic spring loaded adjuster.

Question edited for clarity and make a sentence. Question moved to model category. Normally you tighten the hub nut whilst turning the wheel until it locks solid, then you back off a quarter turn and it should turn freely. https://www.google.com/search?q=Nissan+Frontier.replace+front+wheel+bearings ..

The restarts? That sounds like the classic symptoms of a failing fuel pump

Question edited to add maker. Always include full 'year make model' please. Question moved to model category. video and sales outlets for the part in the link https://www.google.com/search?q=Nissan+Frontier+2WD+4+cylinder+automatic%2C+Speed+sensor ..

https://www.youtube.com/watch?v=F7up1zRKt74

I have a nissan frontier D23 2019 and the driver window will not open and close. Do you have any recommendation or suggestions or technical diagram, so I can troubleshoot it my self ? Thank you in advance. Albert

Notice the spec is inch lbs not foot pounds.

inside fuel tank

Hello. Yes, the camshaft must be removed to 'service' the lifters beneath it. Your car's 'lifters' are dirty; this is why they make a 'ticking' sound' as the engine 'runs'. Good luck and keep me informed; if you want to.

Yes.

Apag? mi veh?culo y se quedan prendidas las luces del carro smart fortwo 2007

Reprogram the key to the new switch .

Hi Kenneth. I'm Tim Dorton. Cruise control is controlled by the electronic throttle control. See https://manuals.co/workshop/nissan/frontier-d40/nissan-frontier-d40-2011-frontier-model-d40-series-service-repair-manual/5874565

Hi Paul. I'm Tim Dorton Nissan Senior Tech. Bad idea to diagnose anything on airbags.The voltage to trigger is very low. Best to have the dealer guys check it with the factory diagnostic stuff. You may find a problem and replace or repair a part, but you will change the resistance of the whole system.

Tools needed:
10mm socket
14mm socket
player's
ratcheting wrench
long and short extension
breaker bar or Big wrench so you can put on ratchet to give you more leverage.

Starter is on the passenger side of truck attached to the transmission.

Start by disconnecting the battery. Something that will greatly help from the top is disconnect the wire from the starter going to the positive battery wire. You will thank god for this later. (it was a pain in the ****)
Remove nut from positive side of solenoid
Remove 10 mm bolt holding stainless steel lines
Remove 14 mm upper and lower bolts (I used ratcheting wrench with extension and 1" wrench to give me leverage)
There is one more 14 mm short bolt that is above tranny pan that you will need a long extension to get to.

Once you remove all bolts starter should almost fall out of place minus wire that you disconnected earlier. The one I had, had gotten caught up with other wires and I finally got aggravated and just broke the wire off to get the starter out. This is not a big deal as the new or re-manufactured starter will have this wire.

Installation:
Make sure to line up the plate right and thread in the top bolt hand tightened.
Do the same as with lower bolt.
line up bracket and thread in the short bolt tight so you don't have to mess with it again.
tighten stainless steel line back together.
Have someone push the wire up you in the upper part of the engine area and plug wire back in.
tighten all bolts and make sure to attach positive batter cable wire to starter.
Reinstall battery and give the key a turn.

Good Luck and please rate 4 thumbs up for the answer

Ask Google you should find them there