20 Most Recent
1977 Chrysler Cordoba Questions & Answers
1977 chrysler Cordoba won't start
this has a electronic spark module box attached to the air cleaner.basically a computer for there was computers.replace this unit if you can find one .
I WANT TO GET MANUEL
Manuals that are of any use at all, are OEM & costly
You have to have one for every vehicle you own, if you
plan on working on them yourself
For about half the vehicles out there ----- Helm.Com & spend
the big bucks
Get the Powertrain Control & Emissions also,as todays cars
are all about diagnosing computer issues & drivability issues
If you were talking about an owners manua,l so you can look up
lamps/bulbs & fuses,the dealers never have had them,
they come one time with a new car & to buy one Helm.Com
or where ever your dealer tells you to go to to get one
98chrysler cordoba wiring diagram when
The fault relates to the electric section and it is the ingnition unit that needs a check. You will need to check on the HT coils for the TRIGGER PULSATING VOLTAGES for the HT to be normal.
If there is absence of HT or low intensity then the ignition system is faulty. Also the trigger from these pulses feed the RPM indication and if the ingnition has fault then the RPM will be irregular.
So check this out using a multimter to confirm.
Noise on exhaust system first part from engine block
That is called the Exhaust Manifold. One side is attached to the side of the engine, and the other side is attached to the end of the Catalytic Converter. If the car is horrendously loud, someone has stolen it. If you can see it under the van, the gaskets just need replacing or the bolts tightening. The Cat often has a flex pipe which can split, in which case it needs replacing.
2004 Chrysler Pacifica. The oil light keeps coming on, I had the oil changed & it still comes on.
When you say the "oil light," do you mean the light that says "Change oil" or are you seeing the red light that indicates low oil pressure?
If you're seeing that red light, that likely means you have low oil pressure and should stop driving immediately, until the problem is diagnosed and repaired. It's also possible to see the oil pressure light on when there's no issue with oil pressure, if the oil pressure sender has failed or there's a connection problem.If the oil light you're referring to is the "change oil" light, you will need to manually reset it for it to disappear. Here's how (from Chrysler):1. Turn the ignition switch to the ON/RUN position (do not start the engine).2. Fully depress the accelerator pedal, slowly, three times within 10 seconds.3. Turn the ignition switch to the OFF/LOCK position.NOTE: If the indicator message illuminates when you start the engine, the oil change indicator system did not reset. If necessary, repeat these steps.
07 chrysler twc 3.8 upper intake tightening sequence
I found a forum post on Jeep Enthusiast Forums that provides the tightening sequence for the 3.8L upper intake plenum of a 2007 Chrysler TWC. Here are the steps:
Remove covering on lower intake manifold and clean surfaces.
Inspect manifold gasket condition. Gaskets can be re-used, if not damaged. Position new gasket in seal channel and press lightly in-place. Repeat procedure for each gasket position.
Position upper manifold on lower manifold.
Apply Mopar® Lock & Seal Adhesive (Medium Strength Threadlocker) to each upper intake manifold bolt.
Install and tighten bolts to 12 N·m (105 in. lbs.) using torque sequence.
Here is the torque sequence for the 3.8L upper intake plenum:
6 2 4
5 1 3
Please note that this information is provided as-is and I recommend consulting a professional mechanic for any further assistance.
How to replace the car starter motor of 2000 chrysler 300M
What is the actual issue are you having with the removal? Starter motors are usually one small wire connector, one large wire connector and two bolts holding it in place.
The most common issues with starter motor replacing are physically getting to it and getting it past other things in the engine bay to get it out.
Not finding what you are looking for?