20 Most Recent 2006 Chevrolet Uplander LT - Page 2 Questions & Answers

Are you referring to the shift cable? More details are needed to answer this

It can be issue with brake system alignment.Get the brake assembly checked.Something is not right and out of its way causing these problem.----------Click the help links mentioned below and go with the troubleshooting solutions to confirm what is exactly faulty in your case:-----Click the link :----Car shakes like the wheels are going to fall off http://technoanswers.blogspot.com/2012/11/car-shakes-like-wheels-are-going-to.html----------

CAR BRAKE PROBLEMS

It can be issue with master cylinder or the problem is there is still some air there in the system,that has to be bleed.Or else the parts replaced are not aligned properly/.I suggest everything back.

There are few help links mentioned below to troubleshoot the issue.

Click the link below and follow its procedure:-----

All types of brake problems and repairs http://howtobyme.blogspot.com/2011/11/abs-and-service-light-comes-on.html

---------- Brake Fade Issue? http://whoisbyme.blogspot.in/2012/07/brake-fade-issue.html

----------- Brake System Troubleshooting? http://technoanswers.blogspot.com/2011/11/brake-system-troubleshooting.html

---------- Car Brake lines have no pressure? http://schematicsdiagram.blogspot.com/2011/12/car-brake-lines-have-no-pressure.html

------------ Car Brakes Dragging? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-dragging.html

------------- Car Brakes grabbing? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-grabbing.html

----------- Car Brakes Making Noise? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-making-noise.html

------------- Car Brakes Pulling? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-pulling.html

---------- Pulsating Brake Pedal? http://repairhelpcenter.blogspot.com/2011/12/pulsating-brake-pedal.html

--------- Spongy brake pedal? http://repairhelpcenter.blogspot.com/2011/12/spongy-brake-pedal.html

---------- Hard Brake Pedal? http://repairhelpcenter.blogspot.com/2011/12/hard-brake-pedal.html

------------ Fading Sinking Brake pedal?

http://whoisbyme.blogspot.in/2012/06/fading-sinking-brake-pedal.html

------------- Feels Like Brake pedal Pulsating http://repairhelpcenter.blogspot.in/2012/06/feels-like-brake-pedal-pulsating.html============These will help.Thanks.

There could be something in the oil that is blocking oil flow in the galleries. Have you checked the condition of the oil for any foreign substances? It could also have something to do with the oil pump operation, but I think it unlikely.

do you have an aux port on the front of the radio? otherwise the aux looks like it should work, but, it doesn't

i don't know. consider going to dealer's parts counter and ask if latch is a replaceable part. this can be a danger to someone using that seat. don't let anyone sith there untill latch is working.

OBD-II Code P0601 is defined as a Internal Control Module Memory Check Sum Error. The PCM or Power Train Control Module performs many vital functions in a modern vehicle, such as management of the Fuel System, Ignition System, Transmission, Anti-Lock Brake and Traction Control systems.

This is the code my mechanic got when the car was hooked up to the machine. ???? What code ? Reduced engine power is related to a problem with the electronic throttle control . Drive by Wire Function and diagnostics by Wells Drive by Wire training

Your O2 sensor regulates the fuel mixture. Your engine will run with a bad O2 sensor, but it will not have the optimal fuel mix. This will usually cause poor fuel mileage and a richer than necessary mixture. This will eventually cause your catalytic converter to plug up, which can be a costly repair. Typical cost to replace an O2 sensor would be in the $100 ball park depending on shop rate, hours to replace, and part price.

You will get all the solution in service and repair manual with diagram which will help you to locate and fix the problem on your own and you will get the manual from the given link https://toolsnyou.com

4.2 inline 6?

The camshaft position sensor is located below the power steering pump. The belt needs to be removed and the power steering pump as well. You need thoroughly clean the surface around the CPS. You don't want any dirt or filth to enter into the engine once you lift and remove the CPS. Any questions please write back. Good Luck.

What kind of problem you have?

If the plastic boots are intact chances are the joints are fine. If they move freely without any binding you should be ok.

It sounds like the A/C compressor clutch is shorted. You will need to have the clutch and / or the complete compressor replaced.

check the multi function switch. ( high / low beams, turn signals)

It may fit but the computer wont agree to it.Dont even try it