2010 Chevrolet Cruze 1.6 - Answered Questions & Fixed issues

http://www.cruzeblog.com/cruze-error-code/ this might help

Key wont open boot - 2010 Chevrolet Cruze 1.6

Vibration only at idle? Could be loose flywheel or harmonic damper. Do you get a clunk when putting from drive to reverse and back? Whoever replaced engine should fix this for you. Oh, it was you? Darn. Check for loose flywheel bolts. You did use a torque wrench and blue locktight, didn't you?

This belt should be under the covers that are in front of the engine. I must caution you that the belt is not placed exactly in the correct position you may have engine failure.

Where di you get this code. What is the problem symptom.

Question edited for clarity Question moved to model category. This is the only mention

error code 94 - I need a code guru pls

Chevrolet Cruze Forums https://www.cruzetalk.com > ... > General Discussion Feb 15, 2016 - Neutral safety/range switch could be slightly out of alignment. Ha, use to be only one wire on these things for the starter solenoid, then added ... error code 67 before engine start ' Chevrolet Cruze Forums Nov 3, 2013 I want help my cruze gave me an error ( code 136) Dec 16, 2017 More results from www.cruzetalk.com ..

Left side of the radiator close to the serpentine belt. Diagrams and videos in the link. https://www.google.com/search?q=chevy+cruze+coolant+temperature+sensor+location ..

Hi. The Ambient Temp Sensor is located in front of your radiator, closer to the passenger side. It is not in clear view. It will be behind some of the finish trim, close to the front grill. Hope this helps.

Maybe it is manufacturer specific code. Check with their service center. If it is OBD2 code P0165 it mean that O2 Sensor Circuit Slow Response (Bank 2 Sensor 3).

Location of orifice tube in the car

About 1,080,000 results (0.79 seconds) Search Results

Chevy Cruze error code 91 - Fixya

www.fixya.com/cars/t18378173-chevy_cruze_error_code_91
Jun 2, 2013 - Chevy Cruze error code 91 What is Error code 91? It appeared ... Ya i know that what is error code 91 it is that ur car key is not there & if shows error code35 then ur car remote key cell losing his power exchange with that cell & ur car is ok. Posted on ... SOURCE: chevrolet cruze 2.0 LT 163cv error. If im not ...

Warning: Cruze Start/Stop button & Immobiliser Design Flaw ...

gearheads.in > Forum > Indian Automotive Scene > Chevrolet > Cruze
Apr 16, 2013 - 10 posts - ‎7 authors 4kms later I realised that I had the Cruze key with me in my pocket ... If the key is outside the car and you try to start it, it throws a Code 91 Error ...

Cruze error code ' Chevy Cruze Blog : Chevrolet Cruze Blog

www.cruzeblog.com/cruze-error-code/
Translate this page Mar 7, 2014 - Cruze Error Code Vehicle message 1 C

If this code appear, the battery of your remote control need to replace.

please advise what about the code 35 of chevrolet cruze 2010

possiable fusable link between battery and main fuse box under the hood or near the starter. follow all the positive wires from the battery one of them has the fusiable link this part of the wire will usually look like its been added with some heatshrink . to tell if its bad the wire will feel soft and bendable. if its good it will feel stiff.also check all fuses under the hood

What fan ? What year is the vehicle ?

Some fixya user told me a website reliable-store it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

Disconnect the battery cables for 3 minutes it should have cleared already after the repair but do this and if the light comes back get the codes read they are fresh ones at autozone and see what comes up

That is not a valid code for your car. If it is P1800, that is the code for a transmission control module Power Control Relay Circuit Open which can lead to harsh shifting (among other things).

Some fixya user told me a website reliable-store. it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

https://www.cruzetalk.com/threads/fuel-pressure-sensor-location.230338 Here is a forum talking about your sensor. It is attached to the fuel pump in the fuel tank. This forum talks about other possibilities of a bad signal.