Top 20 1977 Chevrolet Corvette Questions & Answers

In the picture below the arrow points to the courtesy light fuse.

Park brake switch may be on or the light may have come on because of low brake fluid in the master cylinder. There is a sensor in the reservoir and it turns on the same light as the park brake.

The dealer can do that. A good locksmith likely could, too.

I suggest www.Willcox.com/Corvette . Great site. I’m happy to assist further over the phone at https://www.6ya.com/expert/richard_9a19ee73dfa4686a

the wires coming from the column are for your brakes and blinkers. check fuses, i mean pull them out and inspect. on older cars sometimes they need to be pulled out and put back in from rust. most of the fuse boxes back then were made with metal that will rust and make a bad connection. try that and get back to me. also check with test light on both sides of the fuses.

you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

http://willcoxcorvette.com/instructions/headlamp_and_wiper_small_parts_function_2.pdf REALLY GREAT INFO I’m happy to assist further over the phone at https://www.6ya.com/expert/richard_9a19ee73dfa4686a

Look at the head lite switch for a burned resistor.

check the rods and power to the light motor . The little bushes on the arms wear out and the arms can lock or fall off and jam the motor crank.

There isn,t a fuse for power windows,They use a Ctrcut Breaker, That is on the fuse (Block)

The first thing , this system works on vacuum there are vacuum lines that run from intake to storage can or cans then to light switch inside car then back out to headlights,i would first start by starting the car and listen for vacuum leaks, you may want to follow the vacuum line form the motor checking for splits or cracks in the lines, listen around can, this can sometimes rusts and leaks vacuum, this can or cans are intended to store vacuum and use it when needed, if they are leaking then the lights will work slow until there is enough vacuum to open them, this goes the same for a bad vacuum line and light switch, the light switch is a two part switch, one part supplies power to lights and the other part is vacuum to open lights.you will need to listen for a vacuum leak inside the car at the switch, (headlight switch) .Make sure all lines are good and have no leaks, you will need to make sure the hinges to lights are free and not binding up.

All the diagrams for your corvette can be found here:

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008370b

Headlight wiring is towards the bottom of the page.

Hope this helps, have fun wrenching on that vette.

C4 Corvette 1984-1987 CNC Machined Headlight Gears - Large/Small ' Corvette Mods

bad GM instrument cluster , take it to a qualified repair shop

https://www.corvetteforum.com/forums/c7-general-discussion/3992166-rpo-codes-for-your-car.html http://www.corvetteblogger.com/docs/2014-Corvette-Order-Guide.pdf http://www.corvetteconti.com/blog/wp-content/uploads/2015-stingray-convertible-order-guide.pdf

I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U can also get free manuals

You have an issue with your ABS system and need to find someone with a dinosaur of a scan tool that will access the OBD-1 functions of your system

To remove the battery on the 94 Vette, the side panel needs to be removed.The battery will slide out the side once the hold down bolt is loosened.

just replace the mirror...by the time you replace the switch in the mirror you couldve purchased a mirror cheaper and be happy about it.