20 Most Recent 1999 BMW 323i Questions & Answers

disconnecting the battery should clear the message its worth a try.

the ecm may need resetting as the battery was disconnected use a scan to to reset it and then the immobilizer may operate properly make sure that all wiring harness connections are right and properly connected

No sir BC the difference between year and model the seat assymbly is way different

Could be the shifter cable broken, bad wiring,bad computer, or(If you bought a used on) could be a bad transmission. Unlikely both transmissions would have the exact same problem though.

run the fault codes and look for a sensor / servo fault for the torque converter clutch

have throttle body checked also the MDK throttle motor, make sure that the dealer has followed service bulletin 12 07 99 for procedure to replace the MDK throttle motor also have them check for codes,here are some codes, it could be an expensive job,have them check everything,it is most likely the throttle motor,,throttle body is 600 if they switch it,dont let them do it without checking throttle motor, codes, MS41, MS42 and MS43 engine DME bmw codes... • 1 Ignition coil Cyl 2 • 2 Ignition coil Cyl 4 • 3 Ignition coil Cyl 6 • 5 Fuel injector Cyl 2 • 6 Fuel injector Cyl 1 • 8 Air Flow Meter (HFM) • 10 Coolant Temperature Sensor • 11 Tank Pressure Sensor (EVAP System) or Radiator Outlet Temp (MS43) • 12 TPS or Plausibility - Maximum Coolant Temp (MS43) • 13 Plausibility- Radiator Outlet Temp • 14 Intake Air Temperature Sensor • 15 Plausibility - Cut Out Time • 16 AirCon Compressor - PWM Signal or Plausibility Intake Air Temp (MS43) • 17 Plausibility - Engine Coolant Temp • 18 EWS Signal or Camshaft Sensor (MS43) • 19 Activation VANOS Inlet Valve or Exhaust Valve (MS43) • 20 "CHECK ENGINE" Light Failure • 21 VANOS -Electrical Fault or Activation VANOS Inlet Valve (MS43) • 22 Fuel Injector Cyl 3 • 23 Fuel Injector Cyl 6 • 24 Fuel Injector Cyl 4 • 25 Lambda Sensor Heater -Bank 1 • 27 Idle Control Valve - Malfunction • 29 Ignition Coil Cyl 1 • 30 Ignition Coil Cyl 3 • 31 Ignition Coil Cyl 5 • 33 Fuel Injector Cyl 5 • 35 Aux. Air Injection System Relay • 36 DME Main Relay • 37 DME Main Relay : Delay • 38 Clutch Switch -Plausibility • 39 Brake Light Switch or Brake Light Test Switch • 40 Brake Light Switch or Pedal Value Signal • 42 Multi Function Steering Wheel- Plausibility • 43 Multi Function Steering Wheel: Button • 45 Multi Function Steering Wheel: Port • 47 Temp Sensor -Downstream of Pre-Cat or Torque Limitation Level 1 (MS43) • 48 DME Control Unit -Self Test 1 • 49 DME Control Unit or Torque Monitoring Level 2 (MS43) • 50 EVAP Control Valve or Response Monitoring Level 2 (MS43) • 51 Shut-off Valve -Charcoal Filter or Request Control Unit Reset (MS43) • 52 Solenoid Valve -Exhaust Flap • 53 Idle Speed Actuator • 55 Lambda Sensor Heater -Bank 2 • 56 Ignition Current Feedback Resistor - Open Circuit • 57 Knock sensor -Bank 1 • 58 DME Control Unit -Self Test 2 • 59 Knock Sensor -Bank 2 • 61 Lambda Sensor Heater -Bank 2 Post Cat • 62 Aux. Air Injection System -Switching Valve • 63 DME Control Unit or Ambient Temp Signal via CAN (MS43) • 64 Plausibility - Ambient Temperature • 65 Camshaft Position Sensor (Inlet MS43) • 66 DME Control Unit • 67 DME Control Unit • 68 Tank Venting Valve • 69 Fuel Pump Relay • 70 DME Control Unit • 71 DME Control Unit • 72 DME Control Unit • 74 AirCon Compressor Relay • 75 Lambda Sensor Voltage -Bank 1 • 76 Lambda Sensor Voltage -Bank 2 • 77 Lambda Sensor Voltage -Bank 1 Post Cat • 78 Lambda Sensor Voltage -Bank 2 Post Cat • 79 Lambda Sensor Heater -Bank 1 Post Cat • 80 ABS/ASC interface • 81 MSR Signal -Active too Long • 82 ABS/ASC Interface -Advance Adjustment • 83 Crankshaft Sensor • 90 Exhaust Temperature Pre Cat Conv - Bank 1 • 91 Exhaust Temperature Pre Cat Conv - Bank 2 • 92 Exhaust Temperature Post Cat Conv -Bank 1 • 93 Exhaust Temperature Post Cat Conv -Bank 2 • 94 Auxiliary Air -Air Mass Flow Sensor • 95 Auxiliary Air Valve or Auxiliary Air Hose Blocked • 96 Auxiliary Air Pump - Function • 97 Auxiliary Air -Flow Rate too Low • 98 Auxiliary Air -Flow Rate too High • 99 Auxiliary Air Valve Jammed Open • 100 DME Control Unit -Self-Test Failed • 103 VANOS Error -Inlet Camshaft • 104 VANOS Error -Exhaust Camshaft • 105 VANOS Error -Position Inlet Camshaft • 106 VANOS Error -Position Exhaust Camshaft • 109 Throttle Valve Plausibility • 110 Pedal Sensor Value Potentiometer 1 • 111 Pedal Sensor Value Potentiometer 2 • 112 TPS Potentiometer 1 • 113 TPS Potentiometer 2 • 114 Throttle Valve Final Stage • 115 Reference Voltage -Voltage Regulator 1 or Throttle Pedal Adaptation (MS43) • 116 Reference Voltage -Voltage Regulator 2 • 117 Plausibility -Pedal Position Sensor 1/2 • 118 Plausibility -TPS 1/2 or TPS1/Airflow Plausibility (MS43) • 119 Throttle Valve Sensor -Mechanical Error or TPS2/Airflow Plausibility (MS43) • 120 Plausibility Pedal Sensor or TPS • 122 Engine Oil Temperature • 123 Map Cooling Thermostat Control • 124 Activation DISA Solenoid • 125 Activation Electric Fan • 126 Activation Tank Leak Pump Solenoid • 127 Activation Pump Solenoid • 128 DME/EWS Communication • 129 CAN Signal SMG 1 • 130 CAN Signal ASC -Timeout • 131 CAN Signal Instrument Cluster -Timeout • 132 CAN Signal Instrument Cluster -Timeout • 133 CAN Signal ASC -Timeout • 134 SMG Intervention -Plausibility • 135 Throttle Valve Re-Adaptation Required • 136 Throttle Valve -Spring Test and Limp-home Position Failed • 137 CAN Signal -Steering Angle Sensor • 139 CAN Signal -Tank Level Sensor • 140 Tank Leak Pump Solenoid - Reed Switch Open or Output Stage (MS43) • 141 Tank Leak Pump Solenoid - Reed Switch Stuck Closed or Tank Level Sensor (MS43) • 142 Tank Leak Pump Solenoid - Reed Switch Stuck Open or DMTL Module (MS43) • 143 Tank Ventilation or Tank Leakage (MS43) • 144 Fuel System - Large Leak Recognised • 145 Fuel System - Small Leak Recognised • 146 EVAP System Leak Detected (Small Leak) or Pedal Sensor Supply Voltage Pot 1 (MS43) • 147 Pedal Position Sensor Potentiometer Supply Channel 1 (Pot 2 MS43) • 149 Air Flow Sensor or Pedal Value Sensor Mismatch • 150 Lambda Post Cat Bank 1 Max Limit • 151 Lambda Post Cat Bank 2 Max Limit • 152 Lambda Post Cat Bank 1 Min Limit • 153 Lambda Pre Cat Bank 2 Max Limit • 154 Lambda Pre Cat Bank 2 Min Limit • 155 Lambda Pre Cat Bank 2 No Signal • 156 Lambda Pre Cat Bank 1 No Signal • 157 Lambda Post Cat Bank 1 Min Limit • 159 Lambda Post Cat Bank 2 Max Limit • 160 Lambda Post Cat Bank 2 (MS41) or Throttle Valve Stuck • 161 Throttle Valve - Stuck • 162 Throttle Valve -Control Deviation • 168 Pedal Position Sensor Pot Supply 1 or MAP Cooling Thermostat Jammed (MS43) • 169 Throttle Valve Output Stage Cut off after Fault • 170 DME Control Unit -Self Test Failed • 171 Plausibility - Throttle Valve • 172 Pedal Sensor Potentiometer 1/2 Short Circuit • 173 TPS Potentiometer 1/2 Short Circuit • 174 Throttle Valve Potentiometer 1/2 Adaptation • 175 Pedal Sensor 1 Adaptation • 176 Pedal Sensor 2 Adaptation • 186 Voltage Post Cat Bank 1 • 187 Voltage Post Cat Bank 2 • 188 Voltage Pre Cat Bank 1 • 189 Voltage Pre Cat Bank 2 • 190 EVAP -Reed Switch Open or Voltage Post Cat Bank 1 (MS43) • 191 EVAP -Reed Switch Closed or Voltage Post Cat Bank 2 (MS43) • 192 EVAP -Reed Switch Open • 193 EVAP -Check Hoses • 194 EVAP -Large Leak Detected • 195 EVAP -Small Leak Detected • 196 EVAP -Electrical Valve from LDP Pump or Barometric Pressure Sensor (MS43) • 197 EVAP -Barometric Pressure Sensor • 198 Cat Efficiency during Start -Bank 1 • 199 Cat Efficiency during Start -Bank 2 • 200 Lambda Regulation Bank 1 Pre Cat • 201 Lambda Regulation Bank 2 Pre Cat • 202 Lambda Regulation Bank 1 Post Cat • 203 Lambda Regulation Bank 2 Post cat • 204 Idle Control System -Idle speed not plausible • 208 EWS -RPM Signal Error • 209 EWS -Message Error • 210 Ignition Feedback Resistor (ZSR) • 211 Idle Speed Actuator -Mechanical • 212 VANOS Bank 1 -Mechanical • 214 Vehicle Speed Signal (VSS) • 215 Lambda Sensor Bank 1 or ASC/MSR/EML -Interface not plausible • 216 Lambda Sensor Bank 2 or EGS Position Signal • 217 CAN bus error -EGS Signal not present • 218 CAN module -Warning • 219 CAN module -CAN Offline • 220 Lambda Voltage Range Bank 1 Sensor 1 • 221 Lambda Voltage Range Bank 2 Sensor 1 • 222 Low Coolant Temperature or Lambda Sensor Control (MS43) • 223 Lambda Sensor Switching Bank 1 Sensor 2 • 224 Lambda Sensor Switching Bank 2 Sensor 2 • 225 Cat Efficiency Bank 1 • 226 Cat Efficiency Bank 2 • 227 Mixture Deviation Bank 1 • 228 Mixture Deviation Bank 2 • 229 Lambda Sensor Switching Bank 1 • 230 Lambda Sensor Switching Bank 2 • 231 Lambda Sensor Switching Bank 1 Pre Cat • 232 Lambda Sensor Switching Bank 2 Pre Cat • 233 Catalytic Converter Overall Efficiency Bank 1 • 234 Catalytic Converter Overall Efficiency Bank 2 • 235 Lambda Heater Bank 1 Post Cat or Pre Cat Signal (MS43) • 236 Lambda Heater Bank 2 Post Cat or Pre Cat Signal (MS43) • 238 Misfire Cyl 1 • 239 Misfire Cyl 2 • 240 Misfire Cyl 3 • 241 Misfire Cyl 4 • 242 Misfire Cyl 5 • 243 Misfire Cyl 6 • 244 Crankshaft Interval Timing • 245 Aux Air Injection System Bank 1 • 246 Aux Air Injection System Bank 2 • 247 Aux Air Injection System -Incorrect Flow Detected • 248 Pre Cat Converter Efficiency -Bank 1 • 249 Pre Cat Converter Efficiency -Bank 2 • 250 Tank Venting Valve -Function • 251 Tank Ventilation Diagnosis Error • 252 Tank Ventilation System Vacuum • 253 Activated Charcoal Filter Shut-off Valve Stuck Shut • 254 Tank Ventilation System -Large Air Leak • 255 Tank Ventilation System -Valve Stuck Open

get a battery at walmart,in less than 2 years,take it back and exchange for a new one,do that every 2 years you will never spend another cent on a battery

What is it failing? There should be an OBDII code that tells you why it is not meeting the smog requirements. Read the code and post it, then we can help

I would recommend checking for an intake air leak. Under the intake is a crankcase vent valve that can rupture as well as lines connecting to it. I would also check the rubber bellows from the air mass meter to the intake and make sure they are not split or torn which is also common.

cd magazine/ player is going bad. most likely its the springs that keep it balanced while it spins the discs If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

You don't list what the problem is but I am assuming the passenger window is not going up or down. If it works from the driver side and not the passenger side then it is the passenger switch. If it does not work from either side it is the driver side switch. They are about 50 dollars and very easy to replace.

Check IAC, TPS, & MAF

Replace battery.

Bad hose Freeze out plug on the Block is NG follow the drip

Are you saying just the keyless entry (with the buttons on the key) will not remotely open the doors? Can you insert the key in the lock on the door and manually open the door? There is a procedure to "program" the remote/key but you have to be inside the vehicle with all doors close. I'll be happy to tell you the procedure if you're talking about the keyless/remote entry. You can reply here or feel free to email me directly at [email protected]. Wish I could be more help but need further information in order to help you.

Was the tire able to cause any damage to the wheel?