2005 Acura TL Automatic - Answered Questions & Fixed issues

Usually ABS and some Check Engine light codes are "hard codes" which means they cannot be turned off until what set code is fixed.

If solenoid you may be able to use an OHM meter to check. OR a live power jump if you know the proper voltage. But, It could be something less than 12vdc. Double check all connections. Polish all spade connectors.

O2 sensor no activity bank one sensor one This is the first sensor in the exhaust system on the # 1 cylinder side on engine usually in exhaust manifold.

Maybe.If the cooling system is working correctly, the only thing the thermostat does is make the engine reach normal operating temp in a short period of time. The engine is designed to run at 190 - 210 degrees as much as possible.If you leave the thermostat out, it may run cooler, but you will get a check engine light at some point in time if the engine does not reach 190 degrees within 5 or 10 min. And when the check engine light comes on the performance will drop off. And it will use more fuel.

Any poor performance of the transmission with indicator lights on the dash mean you have problems that need to be resolved immediately...

We want to help you. I do not understand what you are asking. Please have someone help you reword your question so we may better assist you.

Do you get warning lights on the dash ?If yes, a mechanic would check for voltage at the starter.The circuit between the key switch and the starter has a neutral or clutch safety switch that could have failed.

First I suggest scanned the computer in order to know exatly what faul code is stored there, could be a adjust problem or wheel speed sensor go to bad. Additionally, check and test valve body trans solenoids.Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.Thank you for using FixYa, have a nice day.

My man tgs 26.440 malfunc eng contrl dont start

Acura's and honda door handles are a little tricky to do.
make sure the window is all the way up.Then
1. u must remove the inside door panel.
next there is a plug on the inside edge of the door . remove this plug.
2. there is a 10mm bolt that hold the door handle on.
on some honda's and acura's door there will be a latch connecting rod. you will need a small tipped screw driver to remove this.
3. next there will be a 10mm bolt connecting the handle to the door inside. remove this bolt.
once the bolts carefully lift the handle upwards to remove the handle from the outside of the door.
At this point u can remove the door latch and other items that u wish to replace.
To install.. reverse this procedure.
Note.. is some cases there will be connecting wires to the handle and door latch itself. they must be disconnected prior to removeing and other components. Its a pain to do, but if u do not do this the connections could break and it is even harder to repair.
Take your time and don't force the parts apart. they are only plastic

no info generic answer if directional move lever off if hazards push button off if check engine have scanned for trouble code

Check the OBD codes.

Normally an inline fuse on the power wire. The is a fuse to the 'Premium Amplifier'. https://www.autogenius.info/acura-tl-2013-fuse-box-diagram/ ..

DTC P1750: Mechanical Problem in Hydraulic Control System of A/T Clutch Pressure Control Solenoid Valve Assemblies A and B, or Problem in Hydraulic Control System

NOTE:
• Record all freeze data and review General Troubleshooting Information before you troubleshoot.
• Keep these replacement solenoid valves on hand:
• A/T clutch pressure control solenoid valves A and B
1. Check whether the OBD II scan tool indicates another code. Does the OBD II scan tool indicate another code? YES - Perform the troubleshooting flowchart for the indicated code(s). Recheck for code P1750 after troubleshooting. NO - Go to step 2.
2. Turn the ignition switch OFF.
3. Replace the A/T clutch pressure control solenoid valves A and B.
4. Reset the PCM memory with the PGM Tester or by removing the BACK UP fuse in the passenger's underdash fuse/relay box for more than 10 seconds .
5. Drive the vehicle for several minutes in 1st, 2nd, 3rd, 4th, and 5th gears in the position.
6. Recheck for code P1750. Does the OBD II scan tool indicate code P1750? YES - Replace the transmission. NO - The problem has been corrected

There is no way to do a full alignment on any vehicle without a proper alignment setup. Do you have a spare $20,000 to invest in one?

Likely the tranny is shot. My 2002 TLs tranny died @ 21k miles and the replacement died with only 60k miles. $3500 fix.

GET THE SERVICE AND REPAIR MANUAL FROM THE GIVEN LINK AND GET ALL THE KNOWLEDGE YOU WANT http://toolsnyou.com/

My personal suggestion would be to go for these repair catalogs. I know this website www.reliable-store.com that i used to buy them from, and they have it all online and it was very good manual. Go ahead, I bet.

The switch is not making contact after depress , change out the switch , find a auto tech you can trust good luck

Did it file any trouble codes?