20 Most Recent 2011 Toyota Camry - Page 8 Questions & Answers

Do they work from actual door switch? My guess is master control on drivers door is going bad.

Wiring, sche matic, electrical diagrams etc are basic contents of these online books they here on this website www.reliable-store.com Must check it out

Dead battery on car?

See your Toyota dealer please

There are a few things you can do if your key fob stops working: 1) Change the battery Batteries don't last forever, you'll be surprised how often it's just a dead battery! Search our YouTube channel on how to change a key fob battery for your specific year, make, and model! 2) Wipe the board The board inside your remote can get a lot more filthy than you think! When the board is dirty it can prohibit the contact to the circuit board when you push down on the button. Simply wiping the circuit board off can make your key fob like new again! 3) Get it checked Go to your local hardware store like AutoZone or Oreilly's. They usually have a RF frequency tester. This little gadget will let you know if your key fob is sending a signal. If it is, you may need to reprogram your key fob to your vehicle 4)The old car battery reset trick I know this sounds absurd, but it works sometimes and is worth trying. If you exhausted all of the options above, disconnect both terminals on your car battery for 10 minutes. Then reconnect them and try your key fob. This has worked for many people and I have no idea why. If you do, please comment below to explain. 5) New fob! It might be time for a new key fob! No need to dread over the expensive costs of a new key fob, at Keyless Entry Remote Fob Inc., you can get a refurbished one for a very affordable price! You won't even be able to tell the difference. Just search your vehicle make, model, and year to purchase a key fob or give us a call at 402-671-5100.

Auto parts stores have replacement battery cables with a short wire with a crimp connector on it that you can use to repair that white wire.

That's the switch that changes from high to low beam .

Very possibly. If all lights go out when you have the tail lights turned and and step on the brake, then almost certainly it's an earth/ground problem. Get a wiring diagram and determine the location of the earth/ground connection for the rear lights.

The best solution you'll get from books at www.reliable-store.com These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

take it in repair

I'm looking for the same Schematic Freeway tcd-0361-1. I hope you've found it.

Then it is time to consult an expert local shop. As you have learned no doubt that throwing parts at the problem gains you nothing.

That could be a variety of different things. My guess would be dirty injectors or change the spark plugs and wires.

most likely blew a fuse or more so a fuse-able-link which is the larger high ampere fuses in the main fuse compartment under the hood.

You will get your solution and all info on service info, repair info, parts info, wiring/electrical/fuse diagrams, error/fault codes, torque specs, PCV, owner's/service/repair/parts/maintenance manuals etc everything this website www.reliable-store.com it's a very good website for vehicle problems even as old as 1991 ford..

The Variable Valve Timing Sensor (Bank 1 Intake Side) or Camshaft Timing Oil Control Valve Assembly are the most likely possibilities. The Engine control module and wiring will produce the same symptoms and a couple other things if you follow the link I posted, but the odds are with the two sensors. P0011 2008 TOYOTA CAMRY - Camshaft Position 'A' Timing Over-Advanced or System Performance Bank 1 Read more: https://www.autocodes.com/p0011_2008_toyota_camry.html Unless you can go through the diagnostics for the code(s) and or symptoms this is a good candidate for a reputable repair facility. Check your local dealerships reputation. If you want to try the diagnostics yourself - http://alldatadiy.com/index.html has the OEM diagnostic charts.

Sound like u have a bad solenoid or it could also be the ignition backing as they like to give problems