20 Most Recent
2010 BMW 7 Series - Page 4 Questions & Answers
My 740 il 1996 traction
The light for the traction control means that it was deactivated manually or is simply inactive. If it was not because of manual deactivation, inspect the fuse other than that the throttle cable for the traction control. There should be a throttle cable for the module that overrides the pedal you have. Check if it was disconnected or loose. If all checks out OK you may have to connect a scanner to the system and retrieve error codes to help accurately pinpoint the issue.
I have a 2002 BMW
that is a fault code for the cam sensor, driver side-the cam position sensor is located to right of the dip stick it is round
with a black wire coming from it, if you trace it back it will lead up
into the igniter housing. Best sourse of action is to disconnect the negative terminal on the battery and let the car sit for about 5 minutes, then connect it (clean terminals while you are waiting, good thing to do no matter what, use steel wool or a wire brush)-if it comes back on, check the connector first-it may just be dirty/loose or you might have a damaged harness. Worse case, you may have to replace the sensor, and it is fairly easy to do on that engine, and not real expensive.
How to change fuelpump on
Hi oddkl23,
The fuel pump is located under the carpet cover in the trunk.It will be right of the spare wheel. You will find a cover with a few screws. Under the cover is the pump unit with a harness connector and about 6 or 8 nuts. The 2 hoses attached to the pump have arrows on them indicating flow. Make note of their position. After disconnecting the harness connector and hoses, remove the nuts, then the pump cover.Be sure to replace the o-ring under the cover when installing the new pump. The pump sending unit can be pulled straight up, but is attached to the pump still in the tank. The pump is secured in the tank with 2 tabs. The tabs are at approximately 9oclock and 3 oclock. Release the tabs and remove the pump unit. (hint:make sure to have a few rags placed around the pump area before removing, so that you can soak up any fuel spilled during repairs).Reinstall in reverse order.
How to recharge air conditioner
involves buying freon haveing a vacume pump and a set of a/c guages and being able to test for leaks.Possibly change dryer unit and know what pressures you have to have. If hose blows it could hurt alot or kill. Please take to professional a/c guy. Cheaper in the long run and if you leak freon into atmosfere big fine hope this helps
I have a 1999 BMW
- There are two Camshaft position sensors. The one this is for is the one by the oil dipstick on the LH side of the engine. If you replaced the other you need to replace this one as well. Both are recommended, in other words when changing one it is recommended to change the other as well.
- If you have any further questions or comments please feel free to ask and thank you for using FixYa.
- That being said I sat in a chat and waited for a response from you for 12 minutes. I hope this answers your question.
Regards,
Tony
I need instruction on how
YOUR TIMING IS CONTROLLED BY DIGITAL MOTOR ELECTRONICS CONTROL UNIT.THERE IS NO TIMING SETTING FOR THE M62B44 ENGINE.IF YOU ARE HAVING IGNITION TIMING PROBLEMS TAKE VECHICLE TO BMW DEALERSHIP THEY WILL HAVE TO USE DIAGNOSTIC SCANNER TO CHECK THE DIGITAL MOTOR ELECTRONICS SYSTEM SINCE YOU HAVE SENSORS THAT CONTROL IGNITION TIMING.
Waht is the measurments for
The gap is .032 if you use an aftermarket plug..
The recommended oem plug is pre-gapped and non adjustable (4 electrode)
If you have more questions.. please include year of car.. or engine model..
Best of luck!
I have the following DME
you may refer to the code in the link below:
http://www.scribd.com/doc/49140934/bmw-airbag
I find it odd that there are a lot of error. I would advise to inspect the wiring harness for the airbags unless there is damage in the control unit. I also advise to have the SRS checked out to ensure they are working. I do recommend that the dealer take a look at this as well since the system involved is related to safety.
2004 745li po368 code camshaft
Intake camsensor bank #1 is located at the back of the right valve cover on the left side above the impulse wheel
Exhaust cam sensor bank #1 is located just to the right of the intake cam sensor no the back of the valve cover
Do you now where # 1 cylinder is that bank one (rule of thumb)
I got problem whene the
Thanks for choosing FixYa and welcome to the site. There could be a few different things to check out. First, I need to know exactly what your car is doing please.
Why can't i get any
you need a special satalite antennae to receive the signal, this means you will need to pay for that satalite tv. if you have a smart phone you can try setting up a video stream over the internet that your smartphone can access. goodluck
When i shut off my
Either a freeze plug or a head gasket is leaking back there. The freeze plug looks like a large metal bottle cap without threads, with the flat part pushed into the block first.
Not finding what you are looking for?