20 Most Recent 2008 Saturn VUE Questions & Answers

look under seat and check wiring and connections if good check power to the switches and test power to the motor- repair or replace damaged or burnt out part

Question edited for clarity and typo. Question moved to model category. in the link https://www.google.com/search?q=2008+Saturn+Vue+3.6.+firing+order ..

Check you have enabled gear shift.

Are any check engine lights on?Try this first: Disconnect your battery and wait about 2-3 minutes. Then reconnect it and see if you can shift out of park.If that doesn't work, you'll need to check the transmission fluid. It could be too low to provide enough pressure to switch gears. It'll need to be checked with the engine warm, idling.If the transmission fluid checks out fine (it's not low or burned/dark colored), chances are there's a mechanical problem with the transmission or shift linkage. Keep in mind the fluid could also have metal and friction particles blocking the flow of oil through the channels, even if it looks ok. Here are a few possibilities of what else could be wrong (not an all-inclusive list):Manual Valve to Detent Lever Link (802)*Broken or missing*Disconnected from the manual valveManual Valve to Link Clip (801)*DisconnectedManual Valve (800)*StuckShift Linkage*DisconnectedValve Body, Channel Plate and Case*Blocked fluid channels

When I have had trouble with V-belts squeal or serpentine belts the belt is loose need to adjust tension or tension pulley bad. Belt wore and needs replacing or some of the pulleys are dragging while rotating or turning, could be bearing for pulley going bad. Check belt is tight, look of high wear a lot of cracks in the belt. You can try loosening the belt and turning the pulley which will turn and see if they odd sounds or stiff to turn. Car Sounds and Diagnostics ' Auto Repair Tips ' Paul Campanella's DE - Paul Campanella's Auto & Tire Center (campanellas.com) How to Diagnose and Fix Belt Squeaks or Squealing Noise Issues - YouTube Loud Squealing Noise From Engine Bay ' How to Check a Serpentine Belt - YouTube

It is integrated into the throttle body with the control motor. View this video for Saturn Vue T/Body issues.: https://youtu.be/1CEJ9TNK8O8

probably is not a light but only a reflector

Start with a wiring diagram.

Disconnect the creative wiring and check the multiple power inputs to the ECM are functioning as prescribed (ignition switch OFF/RUN/START).

Try "Carmin Std" app for free (with ads) wiring diagrams.

Bank 1 is generally the cylinder bank closest to the firewall. Bank 2 is the one closest to the radiator. Sensor 1 is the one in the exhaust manifold. If the OBD code says it is running lean, you find it is covered in black soot when you remove it. With the new one in, you may get a running lean code as it is burning the soot out. Reset the code, it is a false positive. Happened to me last week. https://www.google.com/search?q=sensor+1+bank+2+on+a+2008+saturn+vue+3.5l+v6+location ..

It's just inside the chassis under the vehicle on the driver side just in front of the rear wheel. Its silver and about the size of a small can of beans. It's an in line filter, takes about 1/2 to 1 hour to change with fuel line tools. You dint have to have special tools. A pair of needle nose pliers and a small standard screw driver will do. Park it where you don't mind dumping about a half pint of fuel. have a rag and oil pan to catch the fuel and it be under pressure so be careful taking lose. use the rag to keep the spray from getting on you. then pull the hose towards the pan and if you use a clean pan you can pour the fuel into your mower or back in the tank just not the dirt and rust

1. Switch off the car 2. Pop up the hood and raise it 3. Locate the transmission fluid cap 4. Remove the cap to add fluid 5. Check the owner's manual on what type of fluid your car requires and in what quantity. It is essential to use the right fluid and not anything off the shelf. 6. Remove the dipstick and start filling up the fluid slowly - you don't want to add too little or overfill. 7. Now put back the dipstick, switch on the vehicle and start shifting gears. Remove the dipstick and see the marking to know if you your car has the right amount of fluid 8. Put back the cap by turning it clockwise.

your vechicle has the electronic power steering.which is controlled by power steering module the power steering module receive information from the torque sensors in steering wheel and vechicle speed sensor.when speeds are slowest the steering input that tracks the amount of power assist.THIS TYPE POWER STEERING UNIT DEALERSHIP FIX NEED DIAGNOSTIC EQUIPMENT TO WORK ON THEM.

If you have too much money, I will take some off your hands. All season tires are all season tires. If you want snow tires get a new set of rims then keep snow tires in your garage for the winter and all season tires for the rest of the year. If you cant drive in the snow cant help you with that.

your battery has the volts but not the amps. Get the battery load tested. how old is the battery?

Sounds like a security system issue. Using the key fob to lock and unlock the doors will usually reset the system. You may have to do this procedure a couple of times and see if it works

Pressure has built up in the system possibly from a clogged orifice tube/expansion valve. Replace the orifice tube/expansion valve, thenPull a vacuum on the system and recharge.

At this website www.reliable-store.com I found all complete guide,much better language, complete detail in 800+ pages, ..and they also have live chat for instant help feature

That's usually caused by a misadjusted push rod going into the master cylinder OR a misadjusted brake pedal switch. When either are out of whack it won't let the master cylinder piston return all the way to home, so it covers up the relief port in the M/C. As the brake fluid heats up and expands it can flow back through the relief port, so the pressure continues to build and it actually applies the brakes.