Top 20 2009 Chevrolet Aveo Questions & Answers

Yes anti-theft system and immobilizer lockout. Number one tip, always keep voltage to the ECM using wires or jump leads to the starter motor or the battery leads.. https://www.google.com/search?q=2009+chevy+aveo+reset+security+system

Did it start after you changed the battery? Normally you need to reset the security system and immobilizer. Not having gauges seems to be a known issue, https://www.google.com/search?q=2009+Chevy+Aveo.+gauges+stop+working ..

o2 sensors are purely there to meter the fuel / air into the engine based on throttle position. You need an auto electrician with a pro grade scan tool computer.

What do you mean by causing my car to drop dead?

If your speedometer stopped working and stays at 0 MPH, you should have your car checked ASAP. The most common causes of a speedometer that stopped working include are a faulty speed sensor, a broken gear on the speedometer, damaged wiring, or a faulty engine control unit.

If it's only one cylinder then not likely a MAF or EGR.

More likely a fuel injector or poor compression.

Year, make, model, and mileage?

What causes the P0106 code? The MAP circuit for range and performance problem may have several causes:

• The source of the problem is that the MAP sensor range voltage output is incorrect and out of the programmed input required by the ECU.
• The most common problem is an air intake system vacuum or intake hose being loose, cracked, or missing it's plastic fittings and clamps.
• The wiring or MAP sensor may be bad, brittle, cracked, have a bad connection, or could be too close to the higher voltage consumption components, especially alternators, ignition wires, etc. A poor electrical ground can cause problems also.
• The sensor itself may simply be operating out of range from fatigue in it's internal components.
• MAP sensors must operate within specific ranges to send correct signals for the ECU to coordinate with the throttle position sensor and adjust correctly for proper engine operation.
• If the engine is not in good condition, is missing, has poor fuel pressure, or there is an internal issue with the engine like a burned valve, it can prevent the MAP sensor from getting a correct output.
• The ECU could also be bad but that is rare.

What are the symptoms of the P0106 code? P0106 code will be generally preceded by the Check Engine Light coming on the dashboard display. The vehicle in most cases will not run well, idle poorly, accelerate erratically, run rich, and backfire because the MAP sensor and throttle position sensor will not operate together properly. How does a mechanic diagnose the P0106 code? P0106 is diagnosed with an OBD- II scanner. A qualified technician should then reset the OBD- II fault codes and perform a road test of the vehicle to see if the code comes back. He can observe this by watching live data streaming on his scanner while driving. If the code comes back, then the mechanic will need to do a close inspection to see if the vacuum line and other hoses on the intake system are missing, loose, damaged, or disconnected. If these things appear to be correct, the technician should do a voltage output test on the sensor while the engine is running to determine if the output voltages fluctuate with engine speed and load on the engine. Check that all grounds are operating correctly, since any ground related to the ECU could cause signal fluctuations from sensors. Common mistakes when diagnosing the P0106 code. Diagnostic errors are largely due to not following the proper procedure. First, follow the test procedure in the diagnosis to insure there is no intake air leak like a bad vacuum hose or connection. The technician must verify that the voltage output of the MAP sensor is correct and fluctuates with the engine speed and proper voltage. Idle voltage is normally 1 to 1.5 volts and full throttle is usually around 4.5 volts. Do not buy a new MAP Sensor or ECU unless it is clearly at fault.

most likely there is an issue with the air intake, such as a leak or poorly installed intake. What causes the P0106 code? The MAP circuit for range and performance problem may have several causes:

• The source of the problem is that the MAP sensor range voltage output is incorrect and out of the programmed input required by the ECU.
• The most common problem is an air intake system vacuum or intake hose being loose, cracked, or missing it's plastic fittings and clamps.
• The wiring or MAP sensor may be bad, brittle, cracked, have a bad connection, or could be too close to the higher voltage consumption components, especially alternators, ignition wires, etc. A poor electrical ground can cause problems also.
• The sensor itself may simply be operating out of range from fatigue in it's internal components.
• MAP sensors must operate within specific ranges to send correct signals for the ECU to coordinate with the throttle position sensor and adjust correctly for proper engine operation.
• If the engine is not in good condition, is missing, has poor fuel pressure, or there is an internal issue with the engine like a burned valve, it can prevent the MAP sensor from getting a correct output.
• The ECU could also be bad but that is rare.

What are the symptoms of the P0106 code? P0106 code will be generally preceded by the Check Engine Light coming on the dashboard display. The vehicle in most cases will not run well, idle poorly, accelerate erratically, run rich, and backfire because the MAP sensor and throttle position sensor will not operate together properly. How does a mechanic diagnose the P0106 code? P0106 is diagnosed with an OBD- II scanner. A qualified technician should then reset the OBD- II fault codes and perform a road test of the vehicle to see if the code comes back. He can observe this by watching live data streaming on his scanner while driving. If the code comes back, then the mechanic will need to do a close inspection to see if the vacuum line and other hoses on the intake system are missing, loose, damaged, or disconnected. If these things appear to be correct, the technician should do a voltage output test on the sensor while the engine is running to determine if the output voltages fluctuate with engine speed and load on the engine. Check that all grounds are operating correctly, since any ground related to the ECU could cause signal fluctuations from sensors. Common mistakes when diagnosing the P0106 code. Diagnostic errors are largely due to not following the proper procedure. First, follow the test procedure in the diagnosis to insure there is no intake air leak like a bad vacuum hose or connection. The technician must verify that the voltage output of the MAP sensor is correct and fluctuates with the engine speed and proper voltage. Idle voltage is normally 1 to 1.5 volts and full throttle is usually around 4.5 volts. Do not buy a new MAP Sensor or ECU unless it is clearly at fault.

I don't know what testing you have done? Any applicable hvac trouble codes? Note the diagram, is the compressor clutch energized? In the diagram, top wire for compressor clutch is voltage. The bottom wire is ground. Check voltage and ground with everything turned on, use a test lite. There are fuses involved, also. Could be problem with pressure switch?

https://www.youtube.com/watch?v=8WjDMXCkjIw https://www.youtube.com/watch?v=xsfuFcMqvjM You might try calling a auto parts house and ask if the replacement part for your car has two or three contacts points. on the switch. Could it be when you push the clutch the position switch has 2 wires from one contact which goes to different places. Link below Aveo has 3 wires https://www.aveoforum.com/forum/f108/help-clutch-start-sensor-11302/

Is the check engine light on?

If you do not find an overheated brake, how long has it been since your timing belt was serviced?

After driving for a few miles, especially when it is feeling like it is bogging down, get out and feel of the wheel hubs. You might have a brake hanging up.

Most all of these seat units have been assembled at the factory before the seat cover was installed on the seat. Standard repair is to remove the seat from the car, then remove the cover and padding and you should find the plastic or the metal ( or both) framework & armrest mechanism is broken. Repair parts will not be available from a dealer, so a salvage or junk yard may be your next trip. Dealerships will sell you a whole new seat. God bless your efforts.

You may have a bad sensor or a problem. that needs attention.

Check the cars battery
When power is to low it will causes lots of funny noises

no the gas from the compressor is pumped to the condenser to be turned back to liquid to go to the TX valve to be released and be turned back to gas if the condenser is blocked , the gas is turned into liquid by the high pressure generated by the compressor in that line from the condenser on there will be low pressure as the compressor forms a vacuum back to the condenser the low side is the hose from the evaporator to the compressor the high side id the hose from the compressor to the condenser

Has to be programmed . dealer

Interior fuse block wiper fuse.