Mazda MPV - Popular Questions, Answers, Tips & Manuals

Question edited for a lot more clarity and toss in a LOAD of Caps Question moved to model category.

Mazda Mpv LW5W OBD schematic from 17 pin to OBD2 16 ...

Mazda Forum https://www.mazdaforum.com > ... > Mazda MPV Aug 7, 2015 - My Mpv has a 16 pin socket under the left side of the dash, kind of pointing down. The plug in you are looking at is for Mazda dealer ... Diagnostic Connector Type Question - Mazda Forum Nov 23, 2007 Where is OBD connector - '06 Mazda 6 Aug 29, 2010 OBD II Not Communicating - Mazda Forum Dec 26, 2008 Location to perform an engine Diagnostic - Mazda Forum Nov 20, 2007 More results from www.mazdaforum.com

SOLVED: Mazda mpv obd2 connector location

Fixya https://www.fixya.com > ... > MPV > 1998 Mazda MPV Your ground wire connection for the OBD2 connector is located under the dash just below and to the right of the heater controls. More likely that you dont have ... ..

Question edited for clarity. Question moved to model category. Torques, but you need the engine designation code https://www.mazdabg.com/ftp-uploads/Mazda/--Repair%20Instructions--/323,%20626,%20929,%20Miata,%20Millenia,%20MX3,%20MX6,%20Protege,%20RX-7/7920CH03_Camshaft.htm Timing https://www.google.com/search?q=2000+toyota+mpv+2.5+camshaft+timing+marks

ALL CAR LOCKS TO THAT , 1/2 COCKED BLOCKING SO THE KIDS CAN'T FALL OUT OR CAR. BY LAW TOO. so close it fully is the way. if you can get open , try to trip the lock by hand to make sure is is not in the wrong mode open this is something that must be seen ask an autolock smith to demo this fix it.

Question edited for clarity. Question moved to subcategory. It appears to be a known issue. Ideally, you need an auto-electrician to diagnose with a pro grade high level scanner computer. https://www.google.com/search?q=2005+mazda+mpv+no+display+on+dashboard ..

Question edited for clarity. Question moved to sub category. Check out the link and videos. It is next to the battery. https://www.google.com/search?q=1992+Mazda+MPV+dipstick+for+the+transmission+location ..

Check the engine mounting rubbers. That is indicative of the engine moving.

The best way is to use a transfer pump. Never use the electric pump in the tank and don't turn the ignition on with the tank empty. It only take a minute or two to ruin the pump running it dry. Why are you emptying it? https://www.google.com/search?q=2033+Mazda+MPV+drain+gas Transfer pumps for as little as $15. https://www.google.com/search?q=drain+gas+pump ..

You might have to take your vehicle to a mechanic for the headlights to be replaced and have a mechanic to replace them for you.

If the fuel injection light is illuminated on the dashboard of your 1995 Mazda MPV, it means there is a problem with the fuel injection system. Here are the steps you can take to troubleshoot the issue:

1. Check for any other warning lights: If there are any other warning lights on the dashboard, it could be an indication of a bigger issue. Check the owner's manual for guidance on what to do next.
2. Check the fuel level: Make sure the fuel tank is not empty or low. If the fuel level is low, add fuel to the tank and see if the light turns off.
3. Check the fuel injection system components: Check the fuel injection system components, including the fuel filter, fuel pump, fuel pressure regulator, and fuel injectors. If any of these components are faulty, it could cause the fuel injection light to illuminate.
4. Check the connections: Check all electrical connections related to the fuel injection system. Loose or corroded connections can also cause the fuel injection light to come on.
5. Check the diagnostic trouble codes: If you have an OBD-II scanner, you can use it to check for diagnostic trouble codes (DTCs) that could be causing the fuel injection light to come on. The DTCs will give you a clue as to what the problem is.

If you are unable to diagnose the problem on your own, it's best to take your Mazda MPV to a certified mechanic who can diagnose and repair the issue for you.

If your looking for a route to run the wires follow the existing wiring loom through the firewall. The loom uses pre-drilled holes with rubber inserts so you won't have to drill any new holes. You can use small zip ties to secure it to the bundle of wires on the loom to keep thing tidy.

This is one of those where you need to play detective. Check the silly stuff first. Is it a piece of loose body trim or a loose mud flap rattling as you drive along? Is it a decorative 'stick on' accessory like a window flag flapping? Is there something stuck under the vehicle like a tree branch or a bit of trash you've driven over. Is it a 1, 2 or 3 clicking sequence then nothing, or is it more of a constant 'machine gun' click. Start the vehicle when the engine is cold and listen for the noise. Let the engine sit at idle until it is up to working temperature, (About 10 to 15 minutes from totally cold). DON'T rev the engine! Is the noise there when it's cold or does it start when the engine has warmed up? Does the noise happen only when driving, only while parked or both? Does it change with road speed, (faster when you press the gas and in gear, and slows when you brake), or with engine speed, (Put it in neutral and gradually press the gas pedal while you listen for any change in the noise)? Does cornering affect the sound? Use the comment button below and I'll see what extra help I can give you.

Remove the rocker arm, set to TDC and instal again.

$12.60 https://www.rockauto.com/en/catalog/mazda,2004,mpv,3.0l+v6,1433130,electrical-switch+&+relay,horn+relay,3468 Relays are in the fuse box by the engine. Diagram is on the lid. Pull out the old on and insert the new one. https://www.carcarekiosk.com/video/2006_Mazda_MPV_LX_3.0L_V6/fuse_engine/replace ..

If you keep driving it while it's overheating you can warp the cylinder head and damage the engine. See this post on most common causes of overheatinghttps://ricksfreeautorepairadvice.com/my-car-is-overheating/

To remove the cup holder/ashtray in a 2004 Mazda MPV, you can follow these steps:

1. Open the cup holder/ashtray and locate the small tab on the right-hand side of the unit.
2. Using a flathead screwdriver or other suitable tool, gently press down on the tab to release the retaining clip.
3. While holding down the tab, pull the cup holder/ashtray unit towards you to release it from the center console.
4. Once the unit is free, disconnect any wiring harnesses or light bulbs attached to it, if applicable.

To reinstall the cup holder/ashtray, simply reverse these steps, making sure the retaining clip snaps back into place when reinserting the unit into the center console.

12 no

I don't think you can replace without cloning. The vehicle will not start if code in cluster does not match ECU code. I would suggest you swap the eeproms in cluster.

Hi, as you look at the belt it will rotate to the front of the car. hope this was some help all the best.

What engine do you have.

Check your ignition coil