Ford Cars & Trucks - Popular Questions, Answers, Tips & Manuals

Only way to get the code is dealership or someone with a radio programmer aka auto scanner

I'm sorry, a 1994 does not have a limp mode. If you have exploded the sprag and the transmission is full of debris, it's time for a rebuild or replacement.

That's the Achilles heel of modern cars. Shops don't want to take on a repair that likely will exceed the value of the car and then the owner just walks away after the shop has a couple grand into it and it still doesnt work or it keeps comming back ever other week.

If there's a vocational school near by that teaches automotive repair, they might use it as a case study. But you'll still need to provide a functional SJB. Used from eVendors $75-100 or you can send your unit to be repaired for $250-$300.

According to this yes it does. https://www.google.com/search?q=2000+ford+taurus+se+pats+module ..

You are questioning the answer from full time vehicle electronics technician who does this 5 days a week and is our Fixya vehicle electronics Expert when he isn't. He has access to all the Ford technical bulletins and schematics. This is a Fixya Tip I put up based on an answer given by Jeff on GM Passlock. Yours is similar but different. If Jeff say it needs programming, it does. https://www.fixya.com/cars/r29887709-gm_passlock_security_system Mobile Locksmith https://www.google.com/search?q=mobile+auto+locksmith+near+me Please update to how you get on. Thanks. ..

Adding aftermarket radios seldom works like you expect because the radio head and amplifier are connected to, and monitored by the BCM. Safety warnings and door chimes are played by the BCM via the radio system. It was all designed as a seamless unit on a computer network. Phone Crutchfield, they do all the harness kits and will give you good free advice. Or go to a car audio installer, as they have the programming equipment.https://www.google.com/search?q=2003+ford+taurus+wiring+kit+for+the+amplifier..

Contact your Ford dealer.

This could be two different issues. For the dash light get the vehicle plugged into an OBD scanner or a diagnostic system to check for Trouble Codes. These will give clues as to what and where the issue could be. Comment below with them and I'l try to help explain them. Unless the problem is with the brake booster most traction control systems do not use a vacuum to operate it. It is usually a set of electronic sensors on the wheels that the ECU uses to monitor tyre grip. As I cannot look at the car myself for that hose you will need to get a good mechanic to look at it. The vacuum hose could go to many things like the EGR system, the Turbo (if fitted) or possibly to the transmission.

for any vehicle on the market, its only necessary to put enough fuel in the tank to register movement of the fuel gauge. if you have added enough to see it move just a little bit, that is plenty, if the vehicle does not start, begin test procedures to properly diagnose the reason it will not start. just a gallon can make most move, but if you have put 3 or 4 gallons is and see no movement, check the gauge circuit including the new float and assembly You have just installed

limited info generic answer ----if wiring request is for the vehicle [chassie etc]look up a repair manual for the van---if for the rv try dealer --rv shops --online forums --using the sub-model [rv model series ]

you have addressed most of the things that cause these codes https://www.google.com/search?q=2006+Ford+Mustang+P0106+and+P2195 MAP Sensor (as opposed to MAF) P0106 Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance O2 Sensor P2195 O2 Sensor Signal Stuck Lean When the O2 sensor reports lean, it is dumping extra fuel which causes carbon fouling. This takes a while to burn off or you can use an 'Extreme Clean' type fuel system cleaner. https://www.cjponyparts.com/resources/mustang-dtc-codes ..

Those are all lean codes. I would verrify that you have proper fuel pressure at the rail. If so, I would look for a vaccum leak.

I would first clean the battery terminals and posts of corrosion (even if you can't see any visibly).

Question edited for clarity. Question moved to model category. In the link https://www.google.com/search?q=2006+ford+escape+o2+sensor+wiring+diagram ..

If the diagram below isn't what you're looking for, can you please elaborate on what you need exactly? Wasn't sure if you need the general location of wiring or a specific wiring diagram.

Question edited for clarity There appears to be a difference between Ford F-250 and Ford 351, so here are both. https://www.google.com/search?q=1986+ford+f-250+serpentine+belt+diagram and Ford 351 https://www.google.com/search?q=1986+ford+351+serpentine+belt+diagram ..

Question edited for clarity and spelling of model. Question moved to model category. Short answer is you can't. The Ford PATS system is very complex and designed to stop exactly what you are trying to do. ECM, BCM, PATS Module and sensors all there to prevent theft. Turn the ignition off, and press the brake pedal. Turn the ignition on and off three times, on the third turn leave the ignition running. Press and release the brake pedal, and then turn the ignition off. Repeat these steps again for a second time. Apr 9, 2020

How do I reset the anti theft on a 2000 ford expedition?

Vehicle History https://www.vehiclehistory.com > questions > how-do-i-... ..

Question edited for clarity. Question moved to model category. Duplicated question deleted and combined. Refresh page to see your question published. Lots of help and videos https://www.google.com/search?q=1990+Ford+Bronco+II.+The+air+conditioner+clutch+is+not+working

89 BII fuse panel diagram

Bronco Corral https://www.broncocorral.com > forums > 89-bii-fuse-p... Does anyone have or know where to get a diagram for the under dash fuse panel? I have no cover on mine and no owners manual, and no idea what fuses are what ...

1990 5.8L Fuse Diagram

Full Size Ford Bronco Forum https://www.fullsizebronco.com > threads > 1990-5-8l-f... Oct 13, 2008 - Hello all, I am new to the FSB. My question to you all is does anyone have a picture diagram of a 78' fuse block panel. I am trying to figure ... 88 Bronco Fuse Chart May 4, 2010 1985 Fuse Box/general electrical diagram - Bronco Forum Sep 6, 2012 86 Bronco Fuse box location - Full Size Ford Bronco Forum Sep 5, 2020 More results from www.fullsizebronco.com

Ford Bronco Fuse Panel Diagrams 1992-1996 ' 2021-2023

LMR.com https://lmr.com > products > ford-bronco-fuse-panel-di... Sep 2, 2022 - Often we hear of the difficulties in finding fuse panel diagrams for 5th Gen (92-96) and 6th Gen (21-23) Ford Bronco, so we at LMR have provided ... ..

Remove the plug completely and check the internal pin and socket contacts. Spray the outside of the male socket with WD40 and offer the two connectors squarely together until it locks. ..

Question edited for clarity. Question moved to model category. Help in the link, but this is a job for a specialist auto electrician. https://www.google.com/search?q=Ford+Bantam+Rocam+1.6i.+How+to+open+a+PCM+main+connector https://www.google.com/search?q=auto+electrician+near+me ..