Dodge Cars & Trucks - Page 3 - Recent Questions, Troubleshooting & Support

The fuse that supplies power for the wiper system is located in the fuse panel under the hood in front of the battery (see picture below). Also below is a diagram of the fuse layout. The fuse you want to check is the fuse in the number 2 position. I hope this helps.

https://www.justanswer.com/uploads/working4ev/2009-02-06_220956_1.JPG

If the brake light switch checked out ok, and there are no brake lights illuminating at all, inspect the wiring harness going from the brake switch to the bulbs themselves. There could be an issue with frayed wiring, wiring that has lost its ground, or a short/open situation.

Question edited for clarity. Question moved to model category. One on each bank

Camshaft position sensor - Engine & Transmission

Dodge Journey Forum https://www.dodgejourneyforum.com > topic > 5405-... Feb 21, 2014 - The Camshaft Position (CMP) sensors are located at the rear of the cylinder head covers and are bolted to the cylinder head. Disconnect and ... 3.5L Camshaft position sensor - Dodge Journey Forum 6 posts Feb 23, 2017 Crankshaft position sensor - Electrical, Battery & Charging 8 posts Jul 1, 2016 Camshaft position sensor bank 1 - Dodge Journey Forum 3 posts May 4, 2020 2014 Dodge Journey Cramshaft and Crankshaft Sensor 7 posts Jan 4, 2018 More results from www.dodgejourneyforum.com ..

Question edited for clarity. Question moved to model category. Diagrams and Videos https://www.google.com/search?q=2017+dodge+ram+2500+tradesman+6.4+serpentine+belt+diagram ..

Question edited for clarity. Question moved to model category. Hi Joe New vehicle? The catch in the female section on the floor is faulty. Try spraying it with WD40 or just go down to the breakers yard and pick up another one. Or do you mean the belt spool doesn't lock? It takes inertia or an abrupt stop to lock it. Head down an empty road with dry road surface at 50 mph and hit the brakes hard and throw yourself forward. https://www.google.com/search?q=2013+Dodge+Ram+pickup+truck.+What+causes+the+seat+belt+not+to+lock ..

This might not be engine related. More information please. Does this happen only when you turn the steering or all the time? Is it just when reversing or both directions? Test this by reversing slowly in a straight line for about about one truck's length then gently start turning the steering wheel. Listen and feel for what happens as you turn the steering. Transmissions can also affect how an engine behaves when their put into gear. Do you know if it has been serviced in the past? Have you had it scanned for OBD Trouble Codes? All cars after 1996 have to have this system fitted. Scanning for codes will tell you if it is a sensor causing the issue. If you have to pay for the service ask at 4 or 5 different places as prices can be VERY different. Comment below with the codes and I'll try to help you more.

This is most likely due to the solder joints inside the radio contracting in the cold.

It is part of the TIPM

Q&A: 2006 Dodge Ram Fuel Pump Relay Location

JustAnswer https://www.justanswer.com > Dodge Repair Jan 20, 2012 - The 2006 Ram does not have a fuel pump relay, it is controlled directly by the TIPM (Totally integrated power module) The fuse box by the ...

What is the 2006 Dodge Ram's fuel pump relay location?

Jerry Insurance https://getjerry.com > Questions Oct 4, 2022 - The 2006 Dodge Ram's fuel pump relay is located in the main fuse box under the hood. Learn more here. 1 answer · Top answer: Your confusion is understandable. You're not finding what you're looking for because the 2006 Dodge Ram's fuel pump relay is located in the main ...

Location of fuel pump relay on my 2006 ram 3500w/ cummins

Fixya https://www.fixya.com > cars > t24983207-location_f... Aug 20, 2014 - It is located on the driver's side of the engine. You will see a yellow handle for the fuel/water separator drain valve at the bottom of the ...

2007 5.9 Fuel Pump Fuse or Relay Location

mopar1973man.com https://mopar1973man.com > topic > 10581-2007-59-... Oct 24, 2015 - I am looking to locate where the fuse or relay is on my 2007 5.9 3500 Ram. I have searched hi and low to no avail so hope someone can give ...

2002 is the year. Dodge is the Maker, Cummings is the supplier of the engine. None of it is the model. Google has some guesses, but basically, you clean that area off, find where the leak is coming from and replace the seal or the gasket. In some cases you can add Seal Reconditioner which makes weeping seals supple again. https://www.google.com/search?q=2002+Dodge+Cummings.+Oil+leak+on+driver+side+motor+near+power+steering+pump ..

This suggests it is a sensor issue. https://www.google.com/search?q=2017+Dodge+Journey+stuck+in+2nd+gear.+trans+line+pressure+too+high ..

What is the etc light on a 2010 Dodge Avenger?The lightning bolt indicator on the Avenger's dash is the Electronic Throttle Control (ETC) light. It signifies a problem with the throttle system that controls the amount of fuel provided to the engine. Problems with the throttle body sensor and the throttle body can cause the lightning bolt to illuminate

Just replace it. It is dangerous without one. https://www.google.com/search?q=2000+Dodge+Durango+neutral+safety+switch+replacement ..

The starter on a 2006 Dodge Durango is located under the vehicle, towards the passenger side. Specifically, it's near the transmission, mounted on the lower side of the engine block. Note that the exact location might vary slightly based on the specific Durango model and engine type. Also, be careful when attempting to remove and replace the starter, as it involves dealing with electrical components which can be dangerous if handled improperly.

Normally when you run out of fuel, you burn out and wreck the fuel pump, they are small, turn very fast and it is the fuel that lubricates and cools them. No power though? check the link for help https://www.google.com/search?q=No+power+to+the+fuel+pump+after+running+out+of+gas+1995+Dodge+1500 Auto Electrician can diagnose in 30 minutes. https://www.google.com/search?q=mobile+auto+electrician+near+me ..

Question edited for clarity. Question moved to model category. In the link, but you could test it with a multimeter or a test lamp. all the wiring https://www.justanswer.com/dodge/343b4-98-dodge-ram-2500-fuel-pump-had-12v-cranking-relay.html More here https://www.google.com/search?q=2000+Dodge+Ram+2500+fuel+pump+wiring ..

Is it the sounds of bacon and egg cooking in a skillet, wet French fries dropped in hot oil or the sounds of cooking soup boiling. Details matters and sounds are very subjective. Let me know, I am a qualified chef, as well a a car expert. ..

Question edited for clarity. Question moved to model category. Help in the link https://www.google.com/search?q=2017+Dodge+RAM+2500+tradesman.+I+need+a+wiring+diagram+for+seat ..

have vehicle scanned for any codes and before throwing parts at it start with basics --test battery was fine is not a diagnosis of its condition check and test connections --fuses --relays ignition switch --key ------- https://www.youtube.com/watch?v=L-JV8C3OvfI

P0340 DODGE - Camshaft Position Sensor Circuit Bank 1 Sensor 1Possible causes- Camshaft Position Sensor harness is open or shorted - Camshaft Position Sensor circuit poor electrical connection - Faulty Camshaft Position Sensor - Faulty starter motor - Starting system circuit - Dead (Weak) battery Tech notes Sometimes and in some models, low battery voltage or a weak starter can can trigger a Camshaft Position Sensor code, also a loose worn cam belt can cause this code. Has the belt ever been replaced?.