kawasaki 2004 Prairie 700 4x4 Logo

Related Topics:

A
Anonymous Posted on Sep 17, 2014
Answered

How do I reset limp mode on a 2004,700 prairie?

Belt light is on and engine falls on its face when you give it throttle.

Answer This Question

1 Answer

William J Valentine

William J Valentine

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Champion:

An expert who has answered 200 questions.
Governor:

An expert whose answer got voted for 20 times.

  • Expert 220 Answers
  • Posted on Oct 20, 2014
William J Valentine
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Champion:

An expert who has answered 200 questions.
Governor:

An expert whose answer got voted for 20 times.

Joined: Aug 05, 2014
Answers
220
Questions
0
Helped
114461
Points
302

Make sure your drive clutch spring isnt broke.

5 Related Answers

Anonymous

  • 323 Answers
  • Posted on Apr 26, 2009

SOURCE: limp mode?

It may have a "loss of prime" code that usually follows a service of the fluid and filter. After you're sure the fluid is full at operating temperature, disconnect the battery for a few minutes and reconnect to see if the code resets. I hope this helps.

Ad

Anonymous

  • 4 Answers
  • Posted on Jul 21, 2009

SOURCE: 98 Catera goes into "Limp Mode" after warm up.

have you check you ignition coil packs.

Ottoniel

  • 202 Answers
  • Posted on Jul 24, 2009

SOURCE: EML, Check Engine, Limp Mode

What is limp mode, and it is MiL light( mal function indicator light)it is not EML. Please specify so i can help

Anonymous

  • 1 Answer
  • Posted on Apr 30, 2010

SOURCE: throttle does not work-wrench light on

I need to know if the TPS in my 2006 Ford Fusion SEL, can be replaced on my own, or does it need to go to a dealer to be replaced?

Jonah Oneal

  • 14092 Answers
  • Posted on Oct 24, 2010

SOURCE: 2003 GMC Sierra 5.3L (has

CODE PO120 - TP SENSOR 1 SIGNAL RANGE PERFORMANCE. CODE P1516 - TAC MODULE THROTTLE ACTUATOR POSITION PERFORMANCE. CODE P2135 - THROTTLE POSITION SENSOR 1 - 2 CORRELATION ERROR. THIS IS A DEALERSHIP FIX YOU HAVE PROBLEMS OR FAULTS IN THE THROTTLE POSITION SENSOR.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I get 1998 Kawasaki Prairie 400 out of limp mode?
Question moved to a better category.

Limp mode is normally activated to protect the engine and is ECU and Sensor driven.

Video and articles in this link.

https://www.google.com/search?q=98+Kawasaki+Prairie+400+limp+mode

..
Read full answer
Apr 15, 2022 • kawasaki 2005 Prairie 360
0helpful
1answer

My 2000 Prairie loses power goin up hill and starts to put wen throttle is fully pushed ..could this be cause belt is loose and should I change spark plug
It could be a bad clutch
Read full answer
Jan 22, 2019 • kawasaki 2004 Prairie 700 4x4
0helpful
1answer

I have Kawasaki prairie . How can you keep timing chain the crank when replacing the top end ?
just loop a wire around it so it doesnt fall in, it'll stay on the crank.
Read full answer
May 06, 2017 • kawasaki 2005 Prairie 360
0helpful
1answer

My 1999 Kawasaki prairie kvf 300 runs smooth but will not rev all the way up to full rpms.
Check that the rev governor/throttle cable adjuster screw has not slipped out of adjustment (lock nut vibrated loose).
Read full answer
Apr 05, 2017 • kawasaki 2005 Prairie 360
0helpful
1answer

Will idle & run at slow speeds, bogs down at higher speed.

Prairie 360 revs high but goes slow (45mph) - Kawasaki ATV Forum

www.kawieriders.com > ... > Kawasaki Brute Force/Prairie/Bayou
Oct 27, 2008 - 2006 Prairie 360, wife's ride, polar white, with 26" Swamp Lites on SS108's. ... that it has a low top-speed...45mph is about as fast as they seem to go. ....air cooled motor theres no real performance there, the P360 wts are light ... Can't put 2005 Kawasaki KVF 360 into gear
Jun 30, 2013
Prairie 360 speed/power issue?
Aug 28, 2012
06 Prairie 360, too many rpms???
Nov 30, 2011
2004 Prairie 360: WOT miss
Nov 9, 2011
More results from www.kawieriders.com
Read full answer
Oct 08, 2015 • kawasaki 2005 Prairie 360
0helpful
1answer

I have a 2007 kawasaki prairie 360 just built engine now it starts just pops an backfires when i give it gas
Carburetor was improperly rebuilt, or timing is off on engine.
Read full answer
Nov 29, 2014 • kawasaki 2007 Prairie 360 4x4 Camo
0helpful
1answer

I installed a new battery in my Kawasaki prairie 650 and know the belt check indicator light is blinking
you need to reset your belt sensor if it reappers then you need a new belt or the sensor is bad
Read full answer
Jul 02, 2014 • kawasaki ATVs
0helpful
1answer

Why does my 2005 360 prairie idle fine when wet but bogs down when u push down on the throttle?
My brother had the same problem on his prairie 400. He was getting water in the electrical connector for his CDI unit. Unplug all of the electrical connectors one at a time and make sure they are dry. Apply dielectric grease to all the connections and plug them back in. I recommend doing this one at a time so you don't mix them up or forget where they go.
Read full answer
Apr 14, 2014 • kawasaki 2005 Prairie 360
0helpful
1answer

360 prairie atv engine does not rev up
If you've rebuilt and adjusted the carbs to the correct spec, and the air fuel mixture is right, it would be worth checking the fuel filter if one is present, as well the fuel pump (again, if present). These are typically the first place to look when you idle fine but die out on throttle.

As for the belt light, it depends on what it indicates. Wear? Tension? If the belt slips, or is too tight or too loose, it could also cause stalling under throttle. With the engine off and cool, check it for cracks, splits and wear, and give it a light tug with two fingers. It should have a small amount of play, but not enough to feel like you could pull it off. If it feels like a steel rod, it may be over tight.

If all of these things are fine, no clogged filters, etc, it's maybe time to look at the distributor, and recheck those carbs.
Read full answer
Feb 26, 2014 • kawasaki 2005 Prairie 360 4x4
0helpful
1answer

2006 kawasaki prairie 4x4 model kvf 360 c belt indicator light reset
On the right hand side of the ATV just under the gear leaver, you will find a grey and black multiplugs, you will need to swap them. Please see the link below. KAWASAKI 360 PRAIRIE BELT RESET
Read full answer
Sep 23, 2013 • kawasaki 2012 Prairie 360 4x4
Not finding what you are looking for?

View Most Popular

2004 Prairie 700 4x4

  • ATVs

Related Question

How do I get 1998 Kawasaki Prairie 400 out of limp mode?

  • kawasaki 2005 Prairie 360

Related Topics

1,679 views

Ask a Question

Usually answered in minutes!

Popular Questions

My 2000 Prairie loses power goin up hill and starts to put wen throttle is fully pushed ..could this be cause belt is loose and should I change spark plug

kawasaki 2004 Prairie 700 4x4

Why do my front brakes on my 1997 Kawasaki Prairie 400 4X4 keep locking up

kawasaki 2004 Prairie 700 4x4

No power to 4x4 actuator

kawasaki 2005 Prairie 700 4x4

Turn key no power

kawasaki 2004 Prairie 700 4x4

I completely sank my Kawasaki prairie 650 4x4. I've changed the plug and plug wires, got any water out of the fuel tank, changed the oil several times and a new fuel filter and clean and dried the air filter, it still wont crank.

kawasaki 2004 Prairie 700 4x4

Top kawasaki ATVs Experts

Brad Brown

Level 3 Expert

19187 Answers

john h

Level 3 Expert

29494 Answers

Renee Knafel-Bullock

Level 3 Expert

404 Answers

Are you a kawasaki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...