Question about RTO 200cc Full Size Four Wheeler ATV

2 Answers

I just put new clutches in 85 honda 250 four trax y are thay steeel sliping

I just put new clutch in becouse it was sliping and now even with new clutch its steel sliping how can i fix it

Posted by Anonymous on

  • Pamela Taurus
    Pamela Taurus Nov 16, 2019

    Check the chain and sprockets, did u adjust the cable ? Or check for fraying of the cable, they will mimic slippage

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • RTO Master
  • 11,405 Answers

Hi there's this website called reliable-store.com and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins
there is one website more but i don't remember its name it was 2 years back bitman something link this
Try these out brother

Posted on Nov 16, 2019

Ad

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Filmmaker:

    Uploaded 5 video answers.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 70 Answers

Sometimes you need to adjust your clutch cable. as the disks wear out you have to tighten it to get it to disengage. if the cable is adjusted too tight then it will slip because it is not taking all the pressure off the disks so they can fully grab. That is where i would start

Posted on Jul 29, 2014

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Honda four trax stuck in frist gear and cant start. How do get out of gear to start?


The front break usually over rides the starter sensors. Squeeze it and try starting . You can try rocking the machine forward and backward while trying to get it into neutral.

Aug 24, 2018 | Honda 2004 FourTrax Foreman ES

1 Answer

Taotao 250 will not move when put in gear


If it`s revving seems it would be the clutch.If it has a load on the engine sometimes the breaks wear (if drum brakes) and bind.Unless the tranny has problems shifter fork, etc. If it`s an automatic check the cvt belt or cvt clutch.

Nov 18, 2017 | ATVs

1 Answer

I have replaced a clutch on a Honda 350 four trax atv 4wd and now it is blowing oil out of breather tube


How Much oil did you put back in the engine?..did you remove the oil filter..??..did you install it back in correctly(they go in ONE way!!). .the engine oil capacity is 2.1 quarts..NO MORE!!

Jul 08, 2017 | Honda 2004 FourTrax Foreman ES

2 Answers

1994 Polaris 300 4x4 want shift into high range just grinds


Bad linkage between shift lever and the transmission.

Apr 07, 2015 | ATVs

1 Answer

Revs badly between gears on my 2007 honda trx 250


Sounds like your clutch is slipping. There is an adjustment on the front of the engine for this. Look for a 14mm nut with a flatblade screw in the center of it. Loosen the lock nut while holding the adjuster screw. Hold the nut and turn the screw in the "decrease" direction (marked on the case above the screw) until resistance is felt. Turn the screw back the other way 1/4 turn and tighten the lock nut while holding the screw in this position. If this does not fix your symptom the damage has been done and internal clutch component replacement will be necessary.

Jan 03, 2015 | ATVs

1 Answer

Why would my 2007 honda 420 not shift into third or fourth gear


It's most likely your clutch I would start there first if that's not it something in the trans is broke like a shift fork

If you need further help, I’m available over the phone at https://www.6ya.com/expert/brandon_79b580f5a99c4386

May 12, 2014 | ATVs

1 Answer

Yamaha 2005 raptor 80- clutch not engaging


ever put a clutch in? 100% sure you have the discs in right? It could very well be that it is adjusted too tight and won't release the clutch. Usually happens when you go from a bad bad over adjusted clutch to a nice new one.

Aug 03, 2013 | Yamaha 2005 Raptor 80

1 Answer

2002 yamaha banshee, it is locking up in 1st gear, all the rest work fine. I put in a new clutch-adjusted the shift lever and adjusted the clutch many times. with no luck. with the clutch plates and...


I am not really understanding what is going on...
.. OK...With ALL the clutch components and the drive chain removed - can you (in each gear) SPIN the main transmission shaft ALOT( 20+ turns) in the correct (drive) direction?..I think its counterclockwise.

It is important to remove the drive chain and all clutch components to do this check. You are checking for a SINGLE CRACKED GEAR TOOTH .. the crack will be at the base of a tooth.

Do this check exactly as described.. you are checking the functionality of the transmission alone. - no clutch-no drive chain. If you do have a cracked tooth, the transmission will only rotate about 340 degrees in either direction.
If it was the clutch giving the problem, it would happen in ALL gears...

After the check.. repost and we'll go from there.

Apr 29, 2017 | Yamaha 2005 Banshee Base

Not finding what you are looking for?
RTO 200cc Full Size Four Wheeler ATV Logo

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top RTO ATVs Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

ROB

Level 3 Expert

858 Answers

Harry Goodwin
Harry Goodwin

Level 2 Expert

353 Answers

Are you a RTO ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...