20 Most Recent
Polaris 2007 Ranger 4x4 EFI - Page 7 Questions & Answers
Where is thermal circuit breaker location on 2011 polaris sportsman 800efi
get the manual and read it?
are you guessing all problems is breaker,
it has both.
why not post the problem first what is dead not told.
key on all fuses/breakers have 12vdc on both sides , if not blown
this is all a tech needs to know, lacking electronics training.
2005 has 20amp CB to the fan.
the manual is not free,
7/7/2022 3:45:19 PM •
ATVs
•
Answered
on Jul 07, 2022
Fuse box location for 550 Artic Cat, where is it?
no info generic answer no yr or model on most atv -under seat right corner of air box by frame can also access thru rear wheel opening https://www.motorcyclemanuals.info/motocycles-atvs/arctic-cat/ https://support.countrycat.com/ fill in your info for free repair manuals
7/1/2022 11:21:28 AM •
ATVs
•
Answered
on Jul 01, 2022
My Suzuki Eiger 400 starts hard then once running is great.
The carburetor choke valve might be stuck open or not closing when the engine is cold. The engine needs a richer mixture to start. Too rich a mixture (flooding) can also cause trouble. Turn the fuel valve off to be sure the carb isn't leaking when not in use. If it smokes black on startup, it's flooding. Also check the condition of the spark plugs.
6/18/2022 6:24:53 PM •
ATVs
•
Answered
on Jun 18, 2022
Wiring Diagram for a wildfire ATV 300 CC
Hi,
You can email the manufacturer in order to get the diagram. If they don't reply promptly, please reach out to them via email. Thank you.
6/14/2022 12:47:16 AM •
ATVs
•
Answered
on Jun 14, 2022
What are the torque settings for kawasaki mule 4010 head gasket
Helping a friend work on a Mule 2510, twin cylinder gas engine. Not sure of the year, somewhere around 1995-96? Can anyone help with cylinder head torque specs? We ordered a service manual but it hasn't come in yet.
https://dolgeneraldgme.com/
6/7/2022 9:53:51 AM •
ATVs
•
Answered
on Jun 07, 2022
How to remove starter on a polaris ace 325
The top bolt is fairly easy to take off.....the positive lead from your voltage regulator(has a red cap on it) that is attached to the the starter is fairly easy to remove. Both are 10 mm socket. The hard part is removing the bottom bolt on the starter.....you can't really see it without removing a few things.....very hard to get at. You can remove the clutch cover and the clutch and everything there and finally remove the back of the clutch cover....but that's a lot of work. I find it easier to remove the air box and air filter.... then you can actually see the hidden bolt on the bottom of the starter with a flash light.... it's still hard to get at....but with a few long ratchet extensions and a a flexible ratchet attachment you can get to it. Once that last bolt is removed....usually a little tap with a hammer will dislodge the starter and it will come out.
5/10/2022 9:41:16 PM •
ATVs
•
Answered
on May 10, 2022
KAWASAKI MULE KAF620M dump bed stuck in up position
limited info generic answer if hydro can be air bound-low fluid-failed pump -valve-seal bent damaged piston--////// manual dump bearings bent damaget brackets lift assist piston damaged
5/4/2022 12:56:07 PM •
ATVs
•
Answered
on May 04, 2022
Not finding what you are looking for?