xboa721 posted an answer for this Hitachi DS18DSAL 18V Compact Pro Lithium Ion Driver Drill (Reconditioned):
"If the switches and power are ok (see other answers)..... They're light screws but a dead..."
xboa721 posted an answer for this Makita Drills:
"After 2.5 years, the batteries are dying. Even if you never used the machine. Sounds like..."
xboa721 posted an answer for this Makita 18V LXT Lithium - Ion Cordless Impact Driver Kit Model BTD140:
"Actually, lithium batteries will often fail after 2 years. Depends on the exact chemistry..."
xboa721 posted an answer for this Makita Drills:
"Sat idle for a few years? The start capacitor on the motor is probably dead. Replacing the..."
xboa721 posted an answer for this Coverking 2001 Chevy Blazer - Trailblazer - Molded Dash Cover:
"Or your charging system isn't working. Check the alternator output. When the car is..."
xboa721 posted an answer for this Gates 1997 - 1998 Buick Regal Accessory Drive Belt W0133-1622907 Prim:
"Tell us what's not working!"
xboa721 posted an answer for this Flex A Lite 2001 Chevy Impala - 3.8L V6 - Electric Cooling Fans:
"Starter motor is the place to start looking. Obvious first: Check all connections. Should..."
xboa721 posted an answer for this Washing Machines:
"Most common screech, kick and stop is something fouling the drum drive. Most common..."
xboa721 posted an answer for this Crafts & Hobbies:
"One sixteenth of an inch 1/16" is 1.58mm or about 1.6mm. The one to remember is 1/8" or..."
xboa721 posted an answer for this Epson WorkForce WF-2540:
"Well, assuming you've got a new glass the printer you have pulls apart quite easily as..."
xboa721 posted an answer for this Epson WorkForce WF-2540:
"If the printer sat for a couple of months not printing there may be dry ink on the magenta..."
xboa721 posted an answer for this Tools & Hardware - Others:
"Well, you've probably already done it but make sure you HAVE removed the motor brushes...."
xboa721 posted an answer for this Epson WorkForce WF-2540:
"Sounds like a line of magenta, actually. Which suggests a number of things that *could* be..."
xboa721 posted an answer for this Culligan Under Sink Water Filter:
"Well the simplest answer is the gasket isn't seated properly. The standard approach is to..."
xboa721 posted an answer for this Culligan Under Sink Water Filter:
"Contact Whirlpool directly. Filters may be faulty however it is likely an installation..."
xboa721 posted an answer for this Tools & Hardware - Others:
"Sediment ALWAYS before carbon. This protects the carbon filter and gives the best service..."
xboa721 posted an answer for this Tools & Hardware - Others:
"Try the basics: plug it in, switch it on, check if it has a fuse and the fuse is good...."
xboa721 posted an answer for this Tools & Hardware - Others:
"There's usually a way to get at least some adjustment. Depends on the spring arrangement..."
xboa721 posted an answer for this Culligan Under Sink Water Filter:
"The rubber washers tend to perish after a while and with the water off the rubber has most..."
xboa721 posted an answer for this Culligan Under Sink Water Filter:
"The bottom half of the canister unscrews. These can get stuck fairly tight and you may..."
xboa721 posted an answer for this Culligan Under Sink Water Filter:
"Replacing water filter cartridges?"
xboa721 posted an answer for this Stanley CT10C Heavy Duty Staple Gun/Cable Tacker:
"Is there a depth adjustment or tension adjustment on the Stanley CT10 stapler?"
xboa721 posted an answer for this Stanley CT10C Heavy Duty Staple Gun/Cable Tacker:
"As far as I can tell this unit does not have an adjustment. Normally such an adjustment..."
xboa721 posted an answer for this Dremel 1550:30 Versatip Tool Kit:
"i can't find instructions for dremel versatip to change the heads how do you do this"
xboa721 posted an answer for this Dremel 1550:30 Versatip Tool Kit:
"The pdf manual is..."
xboa721 posted an answer for this 3M 5/8 x 8 - Low-Melt Adhesive Clear:
"To remove the glue - assuming it is in fact a heat glue - you need to heat it and get it..."
xboa721 posted an answer for this 3M 5/8 x 8 - Low-Melt Adhesive Clear:
"when I had floorboards put in, my little boy stepped on the glue(with shoes) and..."
xboa721 posted an answer for this Delta Woodworking Delta Rockwell 14 Inch Wood/metal Band Saw Manual:
"Tell ya what, I'll pick it up for free, no cost, honest! I'll..er..ah.. make it back on..."
xboa721 posted an answer for this Delta Woodworking Delta Rockwell 14 Inch Wood/metal Band Saw Manual:
"I'm looking at a 14" Rockwell bandsaw tha appears to have been made in the early 1980's. ..."
xboa721 posted an answer for this Delta Woodworking Delta Rockwell 14 Inch Wood/metal Band Saw Manual:
"I just purchased a used Rockwell 14" bandsaw. I need an owners manual"