2
Anonymous posted an answer for this Whirlpool Ultimate Care II LSQ9549L Top Load Washer:
"Machine doesn't agitate or spin. water does pump out, strange clicking noise."
AnonymousAnonymous posted an answer for this Whirlpool Ultimate Care II LSQ9549L Top Load Washer:
"If not a broken belt it may be the motor brushes."
Anonymous
Anonymous wrote a tip for Washing Machines:
"There are a lot of times that some problems can be fixed very easily by the owner..."
Anonymous
Anonymous posted an answer for this Hotpoint Ultima WF860 Front Load Washer:
"Washer may not be level, try adjusting the front feet down a bit to raise the front of the..."
AnonymousAnonymous posted an answer for this Hotpoint Ultima WF860 Front Load Washer:
"Water is pumped out of the soap dispenser tray on a white/60 degree wash as it nears the..."
AnonymousAnonymous posted an answer for this Hotpoint Ultima WF860 Front Load Washer:
"I have a wf860, with test displayed and it dosent matter what I do, it still goes into..."
AnonymousAnonymous posted an answer for this Hotpoint Ultima WF860 Front Load Washer:
"There have been 3 versions of Demo Mode used on these appliances. Version 1(Production to-..."
AnonymousAnonymous posted an answer for this Hotpoint Washing Machines:
"Have you checked the motor brushes to see if they are worn? If they are worn they will..."
AnonymousAnonymous posted an answer for this Washing Machines:
"Lg machine machine drum does not rotate I have changed the hall sensor but still no..."
Anonymous
Anonymous posted an answer for this Hotpoint Aquarius WD63 Front Load Washer/Dryer:
"My clothes are sopping wet when the wash has finished and there is water at the bottom of..."
AnonymousAnonymous posted an answer for this Hotpoint Aquarius WD63 Front Load Washer/Dryer:
"Sounds like a blocked outlet pipe. It may be possible that a small item of clothing i.e...."
AnonymousAnonymous posted an answer for this Washing Machines:
"Possible drum bearings going causing bearing grease to get in to wash."
AnonymousAnonymous posted an answer for this Washing Machines:
"my clothes are coming out with oil stains the shape of the drum holes,what could be the..."
AnonymousAnonymous posted an answer for this Washing Machines:
"Washer worked fine early Sunday, then Sunday evening I was washing and kept getting this..."
AnonymousAnonymous posted an answer for this Washing Machines:
"F11: Pump related. Pump not able to empty water correctly. More blockages to check for:..."
Anonymous
Anonymous posted an answer for this Creda W120VW Front Load Washer:
"Look on You Tube for replacing door seals, there are a couple of videos on there that will..."
AnonymousAnonymous posted an answer for this Creda W120VW Front Load Washer:
"how do you change a door seal ?"
AnonymousAnonymous posted an answer for this Washing Machines:
"Blocked pressure bottle or small hole in pipe from pressure bottle."
AnonymousAnonymous posted an answer for this Washing Machines:
"wont shut off when filling up with water during cycle"
AnonymousAnonymous posted an answer for this Washing Machines:
"Cannot drain excess water from machine model is HNWL3126"
AnonymousAnonymous posted an answer for this Washing Machines:
"Blocked outlet pipe or faulty pump."
AnonymousAnonymous posted an answer for this Washing Machines:
"Could be a blockage in the outlet pipe or faulty pump."
AnonymousAnonymous posted an answer for this Washing Machines:
"our machine wont drain at any drain to spin cycle, but does agitate. Know how to fix?"
AnonymousAnonymous posted an answer for this Washing Machines:
"It's getting hot but is it getting hot enough? Driers have different thermostats for..."
AnonymousAnonymous posted an answer for this Washing Machines:
"If washer is spinning but clothes are wet suspect a partial blockage in the outlet pipe...."
AnonymousAnonymous posted an answer for this Washing Machines:
"the washer won't spin dry. It fills and empties but the clothes are soaking wet."
AnonymousAnonymous posted an answer for this Washing Machines:
"Blockage in pressure bottle or small hole in pressure bottle tube."
AnonymousAnonymous posted an answer for this Washing Machines:
"cold water does not stop at set levels. in other words, if water level is set at medium,..."
AnonymousAnonymous posted an answer for this Washing Machines:
"i have a ge washer model whdsr316g1ww. the belt seems too small cannot get it around..."
AnonymousAnonymous posted an answer for this Washing Machines:
"Have you loosened the motor mounts to help swing the motor closer to the pulley? If you..."
Anonymous
Washing Machines 101 answers Dryers 1 answer
