make it right the first time and you dont have to do it again
teckno posted an answer for this Dewalt Chop Saw D28700:
"you have to pull on it to remove it or use a punch and hammer on the end of armature(gear..."
teckno posted an answer for this Dewalt Chop Saw D28700:
"if brush and spring are in good shape you have a major problem; spark on 1 brush : stator..."
teckno posted an answer for this Welding Tools:
"hi, you have 2 big resistor with ajustable tab on it,check for visual damage on it and..."
teckno posted an answer for this Polaroid Mp3 Music & Video Player 180-4:
"verify if your music format is supported by your player"
teckno posted an answer for this Samsung X360-34P Laptop:
"try f5 or f8"
teckno posted an answer for this ASUS K42F A1 Notebook:
"try to update camera drivers"
teckno posted an answer for this Computers & Internet:
"num lock actived"
teckno posted an answer for this Samsung Series 7 700Z7CH - 17.3" - Core i7 3615QM - Windows 7 Professi:
"software like "file salvage" do that"
teckno posted an answer for this Miller Welding Tools:
"check if 12v go on solenoid of starter when you turn key to start,mesure 12 v on starter..."
teckno posted an answer for this Wagner 705 Power Steamer:
"look at control fuse"
teckno posted an answer for this Makita 10" Dual Bevel Sliding Compound Miter Saw:
"linear bearing problem clean them with brake cleaner and compressed air the balls should..."
teckno posted an answer for this Televison & Video:
"your ethernet cable is home made ?? you connect it to a switch or router?? try to define..."
teckno posted an answer for this Bosch 1199VSR 8.5 Amp 1/2 Inch Hammer Drill:
"check motor brush maybe stuck in dirt or power cord conductor cut"
teckno posted an answer for this Briggs & Stratton Briggs Stratton Vanguard V - Twin Vertical Ohv Engine with Electric Start 23 Hp, 1" X 3 5/32" Shaft, ModelNo. 386777 - 0036 - E1:
"spark plug cylinder compression valve adjust"
teckno posted an answer for this Delta Tools & Hardware - Others:
"adjust knive level"
teckno posted an answer for this Makita Saws:
"look a the disk fabricant website,type brand and model in google"
teckno posted an answer for this Makita Saws:
"look a the disk fabricant website,type brand and model in google"
teckno posted an answer for this Dewalt Saws:
"http://servicenet.dewalt.com/"
teckno posted an answer for this Dewalt Saws:
"discontinued product hard to find part for it"
teckno posted an answer for this Dewalt Saws:
"sure you need to test motor brush, switch , field coil"
teckno posted an answer for this Dewalt Saws:
"http://www.ereplacementparts.com/dewalt-dw708-type-crosscut-miter-saw-parts-c-1009_1163..."
teckno posted an answer for this Dewalt Saws:
"no,you need 240v field coil and armature"
teckno posted an answer for this Dewalt D24000S Heavy-Duty 10-inch Wet Tile Saw with Stand:
"mmm.. motor problem,armature or field coil burned or bearing burn motor housing"
teckno posted an answer for this Dewalt DW745 10" Compact Job Site Table Saw:
"you have armature problem,burned,shorted"
teckno posted an answer for this Dewalt DW744XRS 10-inch Job Site Table Saw w/ Rolling Stand:
"check motor brush,2 cap to unscew with new brush check for spark in motor when running,if..."
teckno posted an answer for this Dewalt Saws:
"unscrew brush cap on each side of motor and pull brush out do it reverse with new one"
teckno posted an answer for this Dewalt DW744S 10" Portable Table Saw with Stand:
"try it with no blade if you have unhabitual noise and vibration,probably need to change..."
teckno posted an answer for this Dewalt DW744X 10" Heavy Duty Portable Tab Le Saw:
"if your field coil is dead,most of the time when you run the motor 1 brush spark more..."
teckno posted an answer for this Ridgid 41935 700 Power Drive 115v Threader:
"you have a wire that touch to the housing of the tool or the windings of the motor, a..."
teckno posted an answer for this Welding Tools:
"try it with no output hose connected to it,it flow a steady 20 cfm?"