1
smokin_duall posted an answer for this 2000 Hyundai Elantra:
"Both of the answers are correct, but I think the info is actually on the edge of the..."
smokin_duall
smokin_duall posted an answer for this 1999 Dodge Ram 2500 4WD:
"If the compass is working and the thermometer is stuck (or wrong), it probably a bad..."
smokin_duallsmokin_duall posted an answer for this 1996 Dodge Ram 3500 Club Cab:
"Try car-parts.com. It's a nationwide used parts listing website that lets you look up by..."
smokin_duallsmokin_duall posted an answer for this 1996 Dodge Ram 3500 Club Cab:
"It's usually the CAD actuator as already mentioned. If that's not it, the last thing to..."
smokin_duallsmokin_duall posted an answer for this 1996 Dodge Ram 3500 Club Cab:
"The trans fluid cooler(s) are draining back into the pan when the truck is parked...."
smokin_duallsmokin_duall posted an answer for this Hyundai Cars & Trucks:
"Many of these Hyundai exhaust manifolds are cast steel not iron. Cast steel can be welded!..."
smokin_duall
smokin_duall posted an answer for this 1996 Hyundai Accent:
"Not difficult but a bit of work. You need to remove the steering knuckle assembly from the..."
smokin_duallsmokin_duall posted an answer for this 2008 Hyundai Elantra:
"The most likely problem is that the crankshaft position sensor failed but it could be..."
smokin_duallsmokin_duall posted an answer for this 2000 Hyundai Elantra:
"The above answer is for a 2001, your 2000 is different, it is like my '99. The big..."
smokin_duall
smokin_duall posted an answer for this Vehicle Parts & Accessories:
"Usually this is a problem with the shift linkage not being correctly adusted to allow the..."
smokin_duall
smokin_duall posted an answer for this Honda Small Engine Carb Repair Tool: Mini-bike Go Kart Scooter Moped Racing:
"It's a pretty big job. You need to be competent (and confident) with tools as well as..."
smokin_duall
smokin_duall posted an answer for this Motorcycles:
"Manual or automatic transmission?"
smokin_duallsmokin_duall posted an answer for this 2002 Dodge Ram 3500 Truck:
"Two actuators can be accessed (enough to move them) without removing it. One is on the..."
smokin_duallsmokin_duall posted an answer for this 1999 Dodge Ram 2500 4WD:
"Not hard, you'll need a special socket to get the axle nut off and getting the bearing out..."
smokin_duallsmokin_duall posted an answer for this 1995 Dodge Ram 3500:
"This sounds like a boost leak, the 12 valves are pretty bullet proof. Make sure that all..."
smokin_duallsmokin_duall posted an answer for this 1996 Dodge Ram:
"Next time this happens leave the key in the on position, open the hood and lift the fuel..."
smokin_duallsmokin_duall posted an answer for this 1996 Dodge Ram 3500 Club Cab:
"Are the tie rod ends tight? Is the trac bar (frame end) tight? The steering boxes on these..."
smokin_duallsmokin_duall posted an answer for this 1995 Dodge Ram 3500:
"Open the hood and look between the battery and the light. You will see the wires going to..."
smokin_duallsmokin_duall posted an answer for this 2001 Dodge Ram 2500 Truck:
"The tuff part is getting to the nuts that clamp the exhaust housing to the exhaust..."
smokin_duallsmokin_duall posted an answer for this 1998 Dodge Ram 3500 2WD:
"When the key is turned to the start position, the pump should run for about 20 seconds. Do..."
smokin_duallsmokin_duall posted an answer for this 1965 Ford Mustang:
"Make sure the carb is bolted tight to the manifold too. Loose nuts can cause this."
smokin_duall
smokin_duall posted an answer for this 2001 Honda CBR 929 RR Fireblade:
"If you have power to the relay and the relay isn't closing, I'd suspect that you have a..."
smokin_duall
Cars & Trucks 18 answers
Vehicle Parts &... 2 answers
Motorcycles 2 answers
