sew king posted an answer for this Juki Sewing Machines:
"want speed change motor pulley to larger size. larger belt from auto store."
sew king posted an answer for this Juki DDL-8700:
"a regular needle wiil sew leather. if its heavy leather get a leather needle the kind that..."
sew king posted an answer for this Juki DDL-8700:
"needle too small u need size 21 needle. screw down the presser foot tension too. if u..."
sew king posted an answer for this Juki DDL-8700:
"machine out of time . the hook is not grabing the loop. make sure u have the scarf of the..."
sew king posted an answer for this Juki DDL-8700:
"your thread is NG or u have a burr on the hook or your thread tension is to tight. if u r..."
sew king posted an answer for this Juki DDL-8700:
"your bobbin winder may not be winding properly. u can adjust this by loosining the screw..."
sew king posted an answer for this Juki DDL-8700:
"take up spring is very important. theres a screw on the right side of the post located on..."
sew king posted an answer for this Juki DDL-8700:
"needle too small or machine out of time. to time machine theres a mark on needle bar...."
sew king posted an answer for this Juki DDL-8700:
"do u have an automatic machine meaning ft is lifted by pressing ft pedal a certain..."
sew king posted an answer for this Juki DDL-8700:
"needle too small. cheap thread. needle not centered in slot of presser foot which will..."
sew king posted an answer for this Juki DDL-8700:
"use lilly white oil and oil flow will not show unless the machine has lots of rpms. tilt..."
sew king posted an answer for this Juki DDL-8700:
"use a pair of side cutter plyers and snap the needle sideways till it breaks or just cut..."
sew king posted an answer for this Juki DDL-8700:
"theres a small hole in the needle bar above the bar sc..w you can stick a needle in there..."
sew king posted an answer for this Juki TL-98Q:
"change to larger needle. heavy goods need at least a #21 needle. lower your needle and see..."
sew king posted an answer for this Juki DDL-8700 Industrial Straight Stitch Sewing Machine, Servo Motor:
"set up on quilting table? wheres the oil pan?? if your machine sews fine straight and..."
sew king posted an answer for this Juki DDL-8700:
"what kinda of mach?"
sew king posted an answer for this Juki Sewing Machines:
"first clean bobbin case loosen thread tension screw and clean under tension spring, hi..."
sew king posted an answer for this Juki Sewing Machines:
"what kind of machine?????/"
sew king posted an answer for this Juki DDL-8700:
"machine is out of time and u probably have burrs on the hook since you broke the plate..."
sew king posted an answer for this Juki DDL-5550 Industrial Straight Stitch Sewing Machine, Servo Motor:
"there two holes on the side plate where the presser ft bar is located. take off the rubber..."
sew king posted an answer for this Juki DDL-8700 Industrial Straight Stitch Sewing Machine, Servo Motor:
"tilt machine back and look at the lifter bar. try moving it now without any pressure on..."
sew king posted an answer for this Juki Sewing Machines:
"of course but how thick are the goods u r sewing and hopefully u r using the right size..."
sew king posted an answer for this Juki DDL-8700:
"you have thread in your bobbin case. try spraying wd 40 and let it soak overnite then try..."
sew king posted an answer for this Juki DDL-5550 Industrial Straight Stitch Sewing Machine, Servo Motor:
"loosen the screw that holds the tension device in place and remove the whole thing. if it..."
sew king posted an answer for this Juki DDL-8700:
"there are two set screws on the wheel under the drive belt. u need an allen wrench. don't..."
sew king posted an answer for this Juki DDL-8700 Industrial Straight Stitch Sewing Machine, Servo Motor:
"ck presser foot tension. even with sightest presser ft tension goods should feed. next ck..."
sew king posted an answer for this Juki Sewing Machines:
"the tip of the needle may be loged in the inside of the hook so the bobbin does not fit..."
sew king posted an answer for this Juki DDL-8700:
"ead the needle raise the presser ft and stomp the power foot down, now check the bubble..."
sew king posted an answer for this Juki Sewing Machines:
"try changing the needle to one size larger otherwise your hook is out of time with needle."