Nick posted an answer for this Zebra Office Equipment & Supplies:
"Depending on the type of connection you are using it could be a Main board issue or..."
Nick posted an answer for this Zebra Z4M Printer:
"There is a printhead hot error that will come up on the printer if it overheats the..."
Nick posted an answer for this SATO Office Equipment & Supplies:
"It won't auto install that driver you need to download the driver and install it manually...."
Nick posted an answer for this Zebra Office Equipment & Supplies:
"Calibrate the media sensors by power cycling the printer. If that does not fix the..."
Nick posted an answer for this Televison & Video:
"Usually that is a horizontal output transistor."
Nick posted an answer for this Printronix Line Matrix P5215 Printer:
"I'm having some issues figuring out exactly what problem you are describing, but I think..."
Nick posted an answer for this Printronix P7220 Matrix Printer:
"There is not a head calibration for this printer. There is a phasing adjustment if your..."
Nick posted an answer for this Zebra GK420 Thermal Printer:
"That printer will work in both direct thermal (no ribbon) and thermal transfer (ribbon)..."
Nick posted an answer for this IBM Infoprint 6500 Matrix Printer:
"That is a boot diagnostic menu and I have no idea how that would have come up in the..."
Nick posted an answer for this Tally Office Equipment & Supplies:
"The Printhead is not where the printer expects it to be. Usually the carriage is jammed,..."
Nick posted an answer for this Printronix P7000 FormLine PN P700502 Matrix Printer:
"IT's stored in the ribbon, as far as I know there is no way to reset it."
Nick posted an answer for this Epson Office Equipment & Supplies:
"The DFX-9000 has a full display and should not have single digit error codes. Are you..."
Nick posted an answer for this Tally Office Equipment & Supplies:
"This is normally caused by a bag AGA sensor. TALLYGEN 447540 AGA ASSY T2265 New Link..."
Nick posted an answer for this Zebra Office Equipment & Supplies:
"Ethernet cable Must be plugged in and the printer must be ready for about 60 seconds..."
Nick posted an answer for this Printronix P7220 Matrix Printer:
"The printer can get out of "phase" and the print will look shaky. These instructions are..."
Nick posted an answer for this Tally Line Matrix T6050 Printer:
"I'm not 100% sure what you are asking here, but on that printer to navigate the menus is a..."
Nick posted an answer for this Printronix Office Equipment & Supplies:
"There are two styles of P7000 a spool ribbon style and a cartridge ribbon style. You are..."
Nick posted an answer for this TallyGenicom Office Equipment & Supplies:
"Sounds like your Controller has failed. There are for kinds depending on graphics..."
Nick posted an answer for this Printronix Office Equipment & Supplies:
"Based on your error you could have a P7000 or a P8000, Either way it is normally the main..."
Nick posted an answer for this OKI MICROLINE 320 Turbo Matrix Printer:
"Remove the plastic shield on the ribbon, you may get a bit of ribbon rub, but it's..."
Nick posted an answer for this Tally T6218 Matrix Printer:
"The power supplies are known for shutting the printer down without any error if that is..."
Nick posted an answer for this IBM 6400 Model 015 Matrix Printer:
"Usually due to a broken platen belt if the motor moves. Platen belt can be bought though..."
Nick posted an answer for this Tally 6306 Matrix Printer:
"There is a short on the hammer drive circuit. It can be caused by the HammerBank ..."
Nick posted an answer for this Epson Office Equipment & Supplies:
"Usually caused by the ribbon feed unit. The gears strip out and stop working. Sorry..."
Nick posted an answer for this IBM 6262 Printer:
"There are 2 kinds of 6262 that have vastly different hammer asm, but most likely you have..."
Nick posted an answer for this Printronix P7005, 7010, 7015, 7205, 7210, 7215, 7220 Ultra Capacity Ribbon (90M Characters) (6 Rbn/B...:
"It is the weld processor PCB that detects the weld. PRINTRONIX 254476 001 RIBBON WELD..."
Nick posted an answer for this Zebra 203DPI Printer:
"When you power that printer on it will automatically calibrate which can kick out up to 6..."
Nick posted an answer for this Dascom T2365 Dot Matrix Printer - Monochrome:
"I've not seen this before I'd assume the Power supply is failing."
Nick posted an answer for this Printronix Office Equipment & Supplies:
"A ribbon stall can be caused by the platen handle being too tight, but if that is not the..."
Nick posted an answer for this Printronix P7000 FormLine PN P700502 Matrix Printer:
"Which chip the ribbon one? I don't think you can do that."
Nick posted an answer for this Printronix LineJet® P7205 Matrix Printer:
"It is supposed to do that while the ribbon runs and it scans the barcode."