2Razor sharp CRT images are my passion
Robert Jones posted a question about Televison & Video:
"was it the single stk 4277?"
Robert JonesRobert Jones posted a question about Pioneer PRO-99 TV:
"what convergence ICs are used?"
Robert Jones
Robert Jones posted an answer for this Pioneer SD-532HD5 53" Rear Projection Television:
"Your set has the same problem with the power supply board that the 510/610/710 series of..."
Robert Jones
Robert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"This has been successfully answered, but here's some more information:Your Pioneer..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"Removing the mirror from your set should NEVER BE DONE FROM THE BACK! If you do your..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"Removing the mirror from your set should NEVER BE DONE FROM THE BACK! If you do your..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"Your Pioneer 710HD has the classic cold solder joint problem endemic to all of this..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"If the pic on your CRT RPTV is bleary, its front viewscreen is not the problem, and no,..."
Robert Jones
Robert Jones posted an answer for this Sony KP-53HS30 53" Rear Projection HDTV-Ready Television:
"Unless I miss my guess, this is a CRT based set, a triple-gun CRT unit. As such it..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"Your Pioneer 710HD has the classic cold solder joint problem endemic to all of this series..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"Your Pioneer 710HD has the classic cold solder joint problem endemic to all of this series..."
Robert Jones
Robert Jones posted an answer for this Pioneer PRO-510HD 53" Rear Projection Television:
"If your Elite 510/610/710 - and the earlier 520/620/720s - works fine when you turn it on..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"If your Elite 510/610/710 - and the earlier 520/620/720s - works fine when you turn it on..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"Along with the above advice, which I concur with, your optics need professional grade..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"If your Elite 510/610/710 - and the earlier 520/620/720s - works fine when you turn it on..."
Robert Jones
Robert Jones posted an answer for this Mitsubishi WT-46809 46" Rear Projection Television:
"That series of model uses the STK 393-110, whose legs don't just go intermittent - cold..."
Robert JonesRobert Jones posted an answer for this Televison & Video:
"Not enough info, but I'll take a stab. What you are describing is known in our trade as a..."
Robert JonesRobert Jones posted an answer for this Televison & Video:
"no reset sequence. usually when the protection kicks in without any warning, it's the..."
Robert Jones
Robert Jones posted an answer for this Hitachi 53SDX89B 53" Rear Projection Television:
"You can find exactly what ICs are used by looking for the biggest heat sink in the unit...."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"When the set goes into protection BANG like that, without any intermittencies, usually the..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"See other solutions to the intermittencies. I think your set can still be remedied by the..."
Robert JonesRobert Jones posted an answer for this Hitachi Televison & Video:
"Replace the conv ICs. Sometimes it's just the soldering involved, DK on Hit. But bottom..."
Robert Jones
Robert Jones posted an answer for this Pioneer PRO-200 60" Rear Projection Television:
"Your link doesn't work, but sounds like you need your conv ICs changed, and any popped..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"If you are still running your set with the intermittencies happening occasionally, TURN IT..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"If parts of your screen obey your commandes while other parts do not, or if the whole..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"If you are still running your set with the intermittencies happening occasionally, TURN IT..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"If you are still running your set with the intermittencies happening occasionally, TURN IT..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"Before you remove the board and send it to me, be sure to run your set FROM DEAD COLD one..."
Robert JonesRobert Jones posted an answer for this Pioneer PRO-710HD 64" Rear Projection Television:
"I am going to out on a limb and say that it has nothing to do with the T4 input. If so,..."
Robert Jones
Televison & Video 89 answers
