1
MissFixIt828 posted an answer for this Singer Sewing Machines:
"Try changing your needle. A dull/damaged/bent needle can cause timing and tension issues...."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"Your needle could be bent.Trying changing your needle and move the hand wheel by hand to..."
MissFixIt828MissFixIt828 posted an answer for this PfaFF Sewing Machines:
"Could be an electronic issue. Take it to your local Pfaff dealer for an estimate on..."
MissFixIt828MissFixIt828 posted an answer for this Singer Sewing Machines:
"The timing is probably out."
MissFixIt828MissFixIt828 posted an answer for this Kenmore Sewing Machines:
"Your reverse assembly needs oil. You should probably take it in to be serviced."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"If it is bunching and looping underneath, it's because either the machine isn't threaded..."
MissFixIt828MissFixIt828 posted an answer for this PfaFF Quilt & Craft Pro 7530:
"It's probably seizing up. You should take it in to be serviced."
MissFixIt828MissFixIt828 posted an answer for this Kenmore Sewing Machines:
"The feed assembly is starting to seize. You will have to take it in to be serviced"
MissFixIt828MissFixIt828 posted an answer for this PfaFF Sewing Machines:
"Take it to your pfaff dealer."
MissFixIt828MissFixIt828 posted an answer for this Bernina Sewing Machines:
"Make sure your feed dogs are not set for free motion or darning. Once you switch them to..."
MissFixIt828MissFixIt828 posted an answer for this PfaFF Sewing Machines:
"Unfortunately you probably need a new board and the parts are no longer available."
MissFixIt828
MissFixIt828 posted an answer for this Rex RX-1804:
"The Janome even feed foot will work with your machine..."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"When the machine is set to straight stitch, adjust the stitch width to the position you..."
MissFixIt828
MissFixIt828 posted an answer for this Brother SQ9000FS 80/120 Stitch & Alpha FONT Computer Sewing Machine, 8x1StepBH 7mmZZ WalkDarn1/4Foot 10Feet Theader 10Lb ExtTable 2CasesXR9000 XR9500:
"Make sure presser foot shank is installed correct. The presser foot bar may also need some..."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"Take it to your local Husqvarna dealer for servicing"
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"The hook timing is out. If it's very new I'm assuming it's still under warranty. Take it..."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"Why are you trying to take it apart? What is it doing or not doing?"
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"Try changing your needle. If it still happens with a new needle, the timing is probably..."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"I think you have to kind of slide it from the back towards you. They are a bit tricky"
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"All sewing machines thread a bit different. Which machine do you have?"
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"Sounds like either the motor is dead or the foot control needs to be replaced. If your..."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"If it's an electronic presser foot lift you will have to take it to a babylock dealer for..."
MissFixIt828MissFixIt828 posted an answer for this PfaFF Sewing Machines:
"Take it to your pfaff dealer. The needle clamp may be worn from over tightening the screw."
MissFixIt828MissFixIt828 posted an answer for this PfaFF Sewing Machines:
"You should take it to a repair tech and see if they will give you a free estimate. If your..."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"I don't recommend you take this machine apart. I am a trained service tech and it's a task..."
MissFixIt828MissFixIt828 posted an answer for this Husqvarna Sewing Machines:
"When the machine is threaded, raise the presser foot. The tension disks will release when..."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"You need a new position bracket. What's happened is you forgot to or incorrectly threaded..."
MissFixIt828MissFixIt828 posted an answer for this Husqvarna Sewing Machines:
"Your machine needs to be serviced. Sounds like it is seizing or may have a broken gear."
MissFixIt828MissFixIt828 posted an answer for this Sewing Machines:
"Your machine needs to be serviced. The reverse assembly is probably starting to seize."
MissFixIt828MissFixIt828 posted an answer for this Husqvarna Viking 1:
"Your screen may need to be replaced. Take it to a husqvarna dealer and see if you can get..."
MissFixIt828MissFixIt828 posted an answer for this Husqvarna Viking 1:
"Your screen may need to be replaced. Take it to a husqvarna dealer and see if you can get..."
MissFixIt828
Sewing Machines 69 answers
