2
Graham Bagwill posted an answer for this Miele Washing Machines:
"The problem could be that the load is to small & it is not distributing correct in the..."
Graham BagwillGraham Bagwill posted an answer for this Amana Washing Machines:
"Make sure the hoses are connected to the correct taps & the right temperature is..."
Graham BagwillGraham Bagwill posted an answer for this Washing Machines:
"There 2 reasons why water will not stop filling. The water inlet valve is stuck open &..."
Graham Bagwill
Graham Bagwill posted an answer for this Kenmore 24032\24036 Top Load Washer:
"Check for something caught in the pump or under agitator. Check that the belt underneath..."
Graham Bagwill
Graham Bagwill posted an answer for this Maytag Atlantis MAV6000 Top Load Washer:
"Check balance spring adjusters are locked off. Could be the base warping, if so it will..."
Graham BagwillGraham Bagwill posted an answer for this Maytag Washing Machines:
"Check lid switch & internal fuse."
Graham Bagwill
Graham Bagwill posted an answer for this Maytag Neptune MAH5500B Front Load Washer:
"Make sure the door has not dropped, if this is the case you can bend it up. Check micro..."
Graham BagwillGraham Bagwill posted an answer for this Maytag Washing Machines:
"Some models the bowl is suspended from the top, check all springs & shafts are..."
Graham Bagwill
Graham Bagwill posted an answer for this Electrolux EW1000i Front Load Washer:
"First of all check filters in hoses & water valves, if ok then water inlet valve may..."
Graham Bagwill
Graham Bagwill posted an answer for this LG WM-2277HW Front Load Washer:
"Sounds like drain pump may be burnt out . Unplug power cord, remove back panel, check..."
Graham BagwillGraham Bagwill posted an answer for this Maytag Neptune MAH5500B Front Load Washer:
"As stated make sure the water in the outlet hoses is not still frozen. The pump is located..."
Graham BagwillGraham Bagwill posted an answer for this Maytag Neptune MAH5500B Front Load Washer:
"First check filters in cold inlet hose & inside cold inlet valve. If ok more than..."
Graham BagwillGraham Bagwill posted an answer for this Maytag Neptune MAH5500B Front Load Washer:
"The main seal has failed allowing water into the main bearings. Replace bearings &..."
Graham BagwillGraham Bagwill posted an answer for this Maytag Neptune MAH5500B Front Load Washer:
"First thing to check after you turn the washer on, wait a few minutes & see if door..."
Graham BagwillGraham Bagwill posted an answer for this Kenmore Washing Machines:
"Check hoses for Blockages or kinks, check belt & belt tension spring. sometimes the ..."
Graham BagwillGraham Bagwill posted an answer for this Kenmore Washing Machines:
"Check hoses for Blockages or kinks, check belt & belt tension spring. sometimes the..."
Graham BagwillGraham Bagwill posted an answer for this LG Washing Machines:
"First things first, check the pump / hoses for blockage, check if the pump is operational,..."
Graham Bagwill
Graham Bagwill posted an answer for this Kenmore Laundry Center with Electric Dryer:
"Yes as the answer above indicates it could be the main bearing(s). Check the the bowl..."
Graham Bagwill
Graham Bagwill posted an answer for this Kenmore 22422 Top Load Washer:
"Most agitators have a screw / bolt in the side or under a cap inside the agitator. Most..."
Graham BagwillGraham Bagwill posted an answer for this Washing Machines:
"I have found that usually another part has caused the control board to fail. If this is..."
Graham BagwillGraham Bagwill posted an answer for this Maytag Washing Machines:
"If the fault is not emptying the water out check the pump & also hoses for blockages...."
Graham Bagwill
Graham Bagwill posted an answer for this LG WM2301H Washer:
"Make sure the washer is level, especially front to back. Do not overload washer. Check to..."
Graham Bagwill
Graham Bagwill posted an answer for this LG WM1814CW Front Load Washer:
"Check that the pressure switch tube is connected to pressure switch. Check that the water..."
Graham Bagwill
Graham Bagwill posted an answer for this Whirlpool WTW6400SW Cabrio Washer:
"Make sure the outlet hose is positioned above the top of the washer, if the hose it to low..."
Graham BagwillGraham Bagwill posted an answer for this Washing Machines:
"Main Bearings & seal are shot, this is a big job & usually attempted by a..."
Graham BagwillGraham Bagwill posted an answer for this Washing Machines:
"All washers have a time delay on the door lock, sometimes this unit burns out. Most..."
Graham Bagwill
Graham Bagwill posted an answer for this LG WM2140CW Washer:
"If yor washer has a drip dry switch make sure it is in the off position."
Graham BagwillGraham Bagwill posted an answer for this Maytag Washing Machines:
"You need to remove the agitator, loosen the tub nut (May already be loose), align bowl..."
Graham BagwillGraham Bagwill posted an answer for this Washing Machines:
"If a mechanical timer is fitted more than likely the timer motor is burnt out. This part..."
Graham Bagwill
Graham Bagwill posted an answer for this LG WT5101HW Top Load Washers:
"Check filter in hose at tap end, if if the hoses screw onto back of machine, check the..."
Graham BagwillGraham Bagwill posted an answer for this Washing Machines:
"Most just clip out, some you have to remove a screw(s)."
Graham Bagwill
Washing Machines 100 answers
Cars & Trucks 1 answer
