GLFIcom posted an answer for this Consew 206RB:
"You probably knocked it out of time. There are two push buttons on the base of the..."
GLFIcom posted an answer for this Sewing Machines:
"Hello, It sounds to me as if your top thread tension is too loose or your bobbin thread..."
GLFIcom posted an answer for this Sewing Machines:
"top thread is knotting up on the bottom even if I switch out thread or bobbins. seclector..."
GLFIcom posted an answer for this Sewing Machines:
"Hello! It sound to me like your needle is dull or old. Old needles get sharpened by the..."
GLFIcom posted an answer for this Sewing Machines:
"the thread keeps breaking, I can't seem to get the right tention, so i need help...."
GLFIcom posted an answer for this Consew 226R2 Sewing Machine:
"I'm very familiar with this model. Unfortunately you have not given enough information..."
GLFIcom posted an answer for this Consew 226R2 Sewing Machine:
"trying to set it up . and were haveing problems getting it to sew"
GLFIcom posted an answer for this Bernina Activa 130:
"I'm not completely familiar with your machine, but I would suggest tightening the..."
GLFIcom posted an answer for this Bernina Activa 130:
"My tension is bad. I've tried adjusting, but no success. The lower thread can be seen..."
GLFIcom posted an answer for this Kenmore 19233 Computerized Sewing Machine:
"1st - When I turn on my machine. If I waite 15-20 seconds it will start sewing on it's..."
GLFIcom posted an answer for this Kenmore 19233 Computerized Sewing Machine:
"I would suggest replacing you foot peddle."
GLFIcom posted an answer for this Kenmore Sewing Machines:
"With the limited information you've provided I would say your needle shaft is bent...."
GLFIcom posted an answer for this Kenmore Sewing Machines:
"needle displacement"
GLFIcom posted an answer for this Brother Sewing Machines:
"upper tension too tight. Have changed tension to almost zero. Have cleaned and oiled..."
GLFIcom posted an answer for this Kenmore Sewing Machines:
"my machine just stopped, can't even turn the handwheel by hand with the bobbin out!"
GLFIcom posted an answer for this Kenmore Sewing Machines:
"The most likely cause of this is thread jammed around the bobbin area. Inspect and clean..."
GLFIcom posted an answer for this Euro-Pro Sewing Machines:
"Hi! Most of the time when this is the problem the two disks that squeeze the thread under..."
GLFIcom posted an answer for this Euro-Pro Sewing Machines:
"on my Dressmaker II, the tension will not change. the thread on the bottom stitch makes a..."
GLFIcom posted an answer for this PfaFF Sewing Machines:
"There is two possible solutions. either the machine has been knocked out of time by a..."
GLFIcom posted an answer for this PfaFF Sewing Machines:
"pfaff creative 2134.....needle is hitting the bobbin casing"
GLFIcom posted an answer for this Juki Sewing Machines:
"Searching the Internet would be your best chance for success, unless you have a local shop..."
GLFIcom posted an answer for this Juki Sewing Machines:
"I have a juki machine I went away and left it in the care of a friend. on my return I..."
GLFIcom posted an answer for this Husqvarna Designer I:
"Check for thread jammed in the bobbin area."
GLFIcom posted an answer for this Husqvarna Designer I:
"main shaft lock"
GLFIcom posted an answer for this Kenmore Sewing Machines:
"From your limited description I believe your needle shaft has been bent. try straightening..."
GLFIcom posted an answer for this Kenmore Sewing Machines:
"needle position displacement"
GLFIcom posted an answer for this Bernina Sewing Machines:
"You've knocked the machine out of time. Is there a manual available to help you..."
GLFIcom posted an answer for this Bernina Sewing Machines:
"Bernina 1000 sewing machine. My needle won't pick up the bobbin thread after experiencing..."
GLFIcom posted an answer for this Consew Sewing Machines:
"I was sewing on my Consew 206Rb-4 when the thread jammed in the shuttle area. I have..."
GLFIcom posted an answer for this Consew Sewing Machines:
"There is still thread binding in the bobbin area. My advise is the remove the bobbin..."
GLFIcom posted an answer for this Janome Sewing Machines:
"Hello, It could be a wad of lint in the upper tensioner disks keeping the disks apart. I..."