1
Jim Chang posted an answer for this Kenmore Elite HE4 Electric Dryer:
"Your Thermal Fuse probably blew, get a Digital Volt Meter from Harbor Freight $5.00,..."
Jim Chang
Jim Chang posted an answer for this Dryers:
"In general the thermal type fuse is located underneath the insulator tape and on the coil...."
Jim ChangJim Chang posted an answer for this Kenmore Elite HE4 Electric Dryer:
"Most likely you tripped the over heat fuse. This will happen if your vent hose is clogged..."
Jim ChangJim Chang posted an answer for this Kenmore Dryers:
"Most likely a blown thermal fuse due to a clogged vent system, inside the machine and/or..."
Jim ChangJim Chang posted an answer for this Kenmore Dryers:
"Have you reached into the back the dryer's vent port? Most will just replace the hose but..."
Jim ChangJim Chang posted an answer for this Kenmore Dryers:
"You door switch may be shorted. check with a Digital Volt Meter for a short."
Jim ChangJim Chang posted an answer for this Kenmore Elite HE4 Electric Dryer:
"Locate your thermal fuse, thermostats and heating element and check the OHM's if it reads..."
Jim Chang
Jim Chang posted an answer for this Kenmore 64892 Electric Dryer:
"Did you have a question?"
Jim ChangJim Chang posted an answer for this Kenmore Dryers:
"Check you vent hose and inside vent port behind the machine for lint/blockage."
Jim ChangJim Chang posted an answer for this Kenmore Dryers:
"It is time to diagnose it. But it sounds like you have a blown thermal fuse that is..."
Jim Chang
Jim Chang posted an answer for this Trimworks 1994-1995 Mercedes Benz E320 E 320 Chrome Roof Trim Moldings 2pc 94 95:
"Check your fuel pressure regulator, back fires are indicators of unburnt fuel and shaking..."
Jim Chang
Jim Chang posted an answer for this 2000 Lexus Gs 300:
"It is your Throttle Position Sensor (TPS), the black component on the side of your..."
Jim Chang
Jim Chang posted an answer for this LG WD-3243RHD Front Load Washer / Dryer:
"Fixed! "LE" code Stator/Motor Error. It was a simple fix and only cost $17.68 at..."
Jim Chang
Jim Chang posted an answer for this Vizio P2 42 in. HD-Ready Plasma Television:
"Fixed! Spoke with PartStore.com, rep stated 6871QCH038C (038C) is the superceded..."
Jim Chang
Jim Chang posted an answer for this LG DU-42PX12XC 42 in. Plasma HDTV:
"If it's new you should be under warranty. If not, you need to replace the Power Control..."
Jim ChangJim Chang posted an answer for this LG DU-42PX12XC 42 in. Plasma HDTV:
"I have a Vizio P42HD but once it is taken apart, it is all LG components. It is your Power..."
Jim ChangJim Chang posted an answer for this LG DU-42PX12XC 42 in. Plasma HDTV:
"You can do the repair yourself, you need about 3 hours to take apart and re-install. Keep..."
Jim ChangJim Chang posted an answer for this LG DU-42PX12XC 42 in. Plasma HDTV:
"6781QCH038C is the correct replacement. There is another replacement part for LG's ending..."
Jim ChangJim Chang posted an answer for this LG DU-42PX12XC 42 in. Plasma HDTV:
"According to Electonia-USA.com the Upgraded Control Board (060Q & 038C) does not require a..."
Jim ChangJim Chang posted an answer for this Vizio P2 42 in. HD-Ready Plasma Television:
"Spent 3 hours removing all what seemed like 100 freaken screws. Took out the OEM..."
Jim Chang
Jim Chang posted an answer for this Vizio VM60P 60 in. Plasma TV:
"Spent 3 hours removing all what seemed like 100 freaken screws. Took out the OEM 038A,..."
Jim ChangJim Chang posted an answer for this Vizio P2 42 in. HD-Ready Plasma Television:
"Spent 3 hours removing all what seemed like 100 freaken screws. Took out the OEM 038A,..."
Jim Chang
Dryers 10 answers
Televison & Video 9 answers
Vehicle Parts &... 1 answer
Cars & Trucks 1 answer Washing Machines 1 answer
