Have worked on most everthing and will tell you anything I know about any item
Bud Hayes posted an answer for this Kenmore Dryers:
"It is most likely a blown thermal fuse located on the blower housing next to the heating..."
Bud Hayes posted an answer for this Heavy Machinery:
"Reverse pressure greater than command pressure. the other is oxygen sensor slow about..."
Bud Hayes posted an answer for this Heavy Machinery:
"Turn key off and start over, turn key on and let it go thru it's check up process before..."
Bud Hayes posted an answer for this Kenmore Washing Machines:
"Unplug the washer for5 to 10 minutes so it will reset"
Bud Hayes posted an answer for this Health & Beauty:
"Turn the charger off and unplug for 30 seconds to do a reset. Be sure you are connected..."
Bud Hayes posted an answer for this Heavy Machinery:
"The 648 was built between 1998 and 2001, your serial number shows to be a 1999 model. It..."
Bud Hayes posted an answer for this Hobart Welding Tools:
"check the brushes on the generator motor"
Bud Hayes posted an answer for this Welding Tools:
"I replaced the one on my welder , found one at surplus center worked great. It could be..."
Bud Hayes posted an answer for this Heavy Machinery:
"Late 1995"
Bud Hayes posted an answer for this Heavy Machinery:
"Check to be sure you have the correct filter installed, it has to good enough to handle up..."
Bud Hayes posted an answer for this Heavy Machinery:
"Your baler is a 2010"
Bud Hayes posted an answer for this Heavy Machinery:
"The alinement is ok, most likely you are not tightening the disc arbor bolt tight enough...."
Bud Hayes posted an answer for this Heavy Machinery:
"remove the 4 bolts holding fan to water pump and slip pulley off, replace with new one."
Bud Hayes posted an answer for this Heavy Machinery:
"Check wire harness where it comes into the cab on the left and crosses over to the right..."
Bud Hayes posted an answer for this Heavy Machinery:
"Look in your operator manual and do the D E F sensor reset"
Bud Hayes posted an answer for this Craftsman Garden:
"Be sure drive belt has not slipped off. mine does that."
Bud Hayes posted an answer for this Heavy Machinery:
"Monitor is a must have for this baler."
Bud Hayes posted an answer for this Heavy Machinery:
"Make sure the gate latch bar is in right position with gate shut and don't operate baler..."
Bud Hayes posted an answer for this Heavy Machinery:
"Get a helper and have them crank engine with starter while you giggle wiggle the pto and..."
Bud Hayes posted an answer for this Heavy Machinery:
"Most likely the ignition coil resistor is bad. Ignition key voltage goes to resistor...."
Bud Hayes posted an answer for this Heavy Machinery:
"The signal light flasher switch is the controller for the flasher lights. Replace the turn..."
Bud Hayes posted an answer for this Motorcycles:
"It needs a 30 S A E engine oil good brand."
Bud Hayes posted an answer for this Heavy Machinery:
"Look in your operators manual and do the calibration guide step by step. That will fix it."
Bud Hayes posted an answer for this Heavy Machinery:
"Valve problem"
Bud Hayes posted an answer for this Heavy Machinery:
"Have you baled with this baler before you put new belts on it? If not be sure all the..."
Bud Hayes posted an answer for this Heavy Machinery:
"The front drive wheels are bolted to drive housing with slotted holes for adjusting..."
Bud Hayes posted an answer for this Heavy Machinery:
"There is no easy way . Route the new cable the same as the old one. Tie the new cable to..."
Bud Hayes posted an answer for this Heavy Machinery:
"It would be easier to first try a thicker heavier grease in the tracker adjuster, use..."
Bud Hayes posted an answer for this Heavy Machinery:
"Use this one."
Bud Hayes posted an answer for this Saturn Cars & Trucks:
"https://www.justanswer.com/saturn/6d6ac-saturn-ls200-reset-anti-theft-system-engine-shutdo..."
Bud Hayes posted an answer for this Heavy Machinery:
"Remove battery cable, hold horn button down, connect battery cable keep horn button..."