Yukon Sport & Outdoor - Others - Page 8 - Recent Questions, Troubleshooting & Support

Request instructions from Woods.

Request instructions from Nort(h)west Territory.

Request instructions from Alpine Design.

Request the instructions from Ozark Trail.

Water is getting into it

Request the manual from the manufacturer/distributor.

The manufacturer/distributor might be able to furnish it.

Request the instructions directly from Great Outdoors.

Contact Wallowa directly to request the instructions.

Detailed step by step instructions for putting up the seabreeze tent

The manufacturer/distributor of the game would be a possible source.

PERHAPS FROM A BUSINESS THAT SELLS THEM .

Try the companies official website to see if they have an instruction manual for your tent or try google then too.

Field & Stream would be a possible source.

Tim-

You probably already know this...Espresso provides user/installation manuals on their website at Link.

What I am surprised to see is that they also offer free technical support by phone or email. The contact information is on the website link above.

Hope this helps.

DIYpro

Unfortunately nowhere. You will have have one made at a sailmakers using the old one as a pattern, or buy a new tent, or a generic tent flysheet. https://www.google.com/search?q=replacement+rain+fly+for+Wenger+Appenzell+3+Room+Cabin+Dome+tent ..

Release the brake/clutch.

The first Egyptian pyramid was 204 feet or 62 meters high, built at the direction on Pharoah Djoser in around 2630 B.C. The tallest was the Great Pyramid at Giza, standing at an impressive 481 feet or 147 meters. The smallest was the Pyramid of Pepi II, which stood at a paltry 172 feet or 52 meters. Just based on Egyptian pyramids, the average height is about 316.5 feet or 96.375 meters. Considering the technology of the day, the pyramid builders were quite impressive to say the least. Hope this helped and best wishes.

The blue and yellow go on the left and right red goes in the middle the shortest blue and yellow go in the center loops

I am looking for a manual for Greatland Outdoors 2 room tent with screen porch item #15710, however, I guessed how the poles go together. I set up the tent by myself, but I recommend 2 people or more, especially if it is windy.

Start by stretching out the bottom of the tent into a square, and stake all of the perimeter tentloops to the ground, starting with the corners, with the stakes directed at a 30 to 45 degree angle under the tent, so the tent cannot easily pull them back out. Leave the yellow cords attached to the tentloops loose, so you can use the cords to help pull up the stakes when you take down the tent.

Now assemble the poles going through the loops across the front of the screen porch. Insert one end of a pole #1 into a pole #2 and thread them through the loops over the entrance to the screen porch. Put the long end of a curved pole #3 through the loops starting from one side, and attach to either side of the 1/#2 you made. Put the long end of another #3 through the loops starting from the other side and attach to the loose end of the #1/#2. You should tie the loose green cords on each corner of the sceen porch to the silver metal rings at the curved end of each #3.
Later, you will do the exact same assembly with a #3 on each side of a #1/#2 for the poles going across the back of the tent and the poles going through the pocket across the middle/top of the tent.

Now insert the small end of pole #4 into the curved end of a #3, then insert the small end of a #5 into the open end of the #4. There should be a rubber foot on the bottom of the #5 pole. Do the same thing for the other side of the porch. With help, you should be able to prop up the front of the sceen porch, pulling aganst the stakes holding the rear floor of the tent, and place the rubber feet of the #5 poles close to the center loops of the floor on each side.

Now prepare the #1/#2 poles for the rear, and attach a #3 to each side and tie the loose green cords to the silver rings on the short ends of the #3s. Prepare a #4/#5 pole the same as the front, and prop up the back of the tent, putting the feet near the side loops of the floor which are about 1/3 from the rear of the tent.

Make another #1/#2/#3, and push it through the pocket across the middle of the tent, and connect the last #3 from the other side. The side supports for the middle are pole #8 with the white clamp on the bottom, and pole #7 slid into pole #8 (The #7 was scraped off both of mine). Leave the #7 mostly inserted into the #8 until after the center is lifted up. The #6 goes on top of #7, and insert the #6 into the curved end of the #3 poles which are already in the center pocket, and tie the loose green cords to the silver rings at the short end on each of the #3s. Now lift up the center with someone helping on the other side, and put the feet of the #8 into or near the yellow loops at the center of each side. Loosen the white clamps and extend the #7 poles until the peak of the tent is at proper height.
Move the feet of the #5 poles closer to the tent, until all is tight, and you should be done!