Yaesu Radio Communications - Recent Questions, Troubleshooting & Support
I have a yaesu ft2900 ham radio when i key the mic it turns off then comes back on help
You have all the making of not enough power to operate the radio and it shuts down to protect itself. Hook the power leads directly to the battery terminals and keep the leads as short as possible. The more wire you have the more resistance and the more resistance the less volts your radio can see. Also be certain you have a good ground connection
Have any side effect to smoke ecigs?
You cannot use that adapter to charge ecigs!
The batteries will hit up & explode because high voltage.
First of all it provides 6V which is too much and all ecigarettes that i know use a MicroUSB port for charging (or firmware update on mods)
Usually any ecig battery or mod will use the default USB voltage which is 5V and max 2.4 Amps.
Do NOT use over 5 volts on ecigs unless you got a special model that asks specifically for that power (very unlikely)
As a side effect from vaping ecigs...all i can recommend is to use more or only VG (Vegetable Glycerine) instead of too much PG (Propilen Glycol) on the liquids.
PG can give some side effects to sensible persons as dry throat, strong coughing, some throat bitterness.
Unfortunately most eliquids use plenty PG because it boosts the flavor!
Can i buy mango flavor electronic cigarette?
Hello,
This is lucy from Cigstar, e cigarette manufacture.
Mango flavour electronic cigarette is available, Please kindly add my contact for further talk, thanks.
Best Regads
Lucy Chen ' Sales engineer
Email: [email protected] Skype:lucy.cigastar
CIGSTAR INTERNATIONAL CO., LTD
Website:www.cigstar.com
Yaesu 101ex has no reccive or transmit
The problem is likely the TX/RX relay. If it is old (and I am sure it is) the contacts likely need to be cleaned, or the relay replaced. It is a common enough relay if you want to replace it. Also, pull each PCB card and clean the contacts with a pencil eraser. Pink erasers are OK but the white ones are better as they aren't as abrasive.
Hope this helps, VE3CMQ
Yaesu ft-100d. Does not rx or tx. Frequency readout blinks on rx. On tx frequency blanks out and icon upper left indicates tx-off. full reset and no change. exchanged local unit and no change.
I am not sure, but this usually indicates that the PLL has lost lock. These days, it could be as simple as a poorly soldered connection. I don't recommend that you try repairing this yourself as there are essentially no user serviceable parts in radios these days.
Radio repairs these days have come down to board swapping because the parts are so tiny that humans have a hard time replacing (and in some cases, seeing) the parts. Yaesu US has a very good reputation for quality repairs so I'd suggest you send it there. They will likely just swap a board out, but that will be less expensive than having someone spending 10 hours trying to find the problem and repairing it. I know, as I work in a radio shop, and if it isn't something real simple, all we can do is do a board swap.
My yaesu ftm 3200 will not power up
Check the fuses and the power supply. Make sure that the power supply has enough capacity to run the radio, at least 20A! Make sure that the power supply is putting out 13.6V.
If you were unfortunate enough to hook the power leads up backwards, then a trace may be blown off the circuit board internal to the radio. Also, it is likely that the reverse polarity diode inside has shorted out. This may cause the fuse to blow when you apply power. If it has blown, it likely took the the trace out inside the radio.
If the power supply and fuses are OK, unless you are competent technically, the only recourse is to take the radio into a shop and get them to fix it. If you were upgrading the firmware inside the radio when it happened, then the radio is likely non-repairable.
I don't recommend ever upgrading a radio's firmware! If it isn't broken, then don't fix it!!
Not finding what you are looking for?